Lexus NX: Brake System (C1A50)

DESCRIPTION

When an electronically controlled brake system malfunction signal sent from the brake booster with master cylinder assembly (skid control ECU) is detected by the clearance warning ECU assembly, DTC C1A50 is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1A50

Brake System

When the power switch is on (IG), a VSC warning light malfunction signal is detected for 1 second or more.

  • Electronically controlled brake system
  • Clearance warning ECU assembly

CAUTION / NOTICE / HINT

NOTICE:

  • After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

  • When disconnecting and reconnecting the auxiliary battery

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

  • After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).

    Click here

PROCEDURE

1.

CHECK FOR DTC

(a) Using the Techstream, check for DTCs according to the prompts on the screen.

Click here

HINT:

After turning the power switch from off to on (IG), wait 4 seconds or more before checking for DTCs.

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes

(b) Clear the DTCs according to the screen on the Techstream.

Click here

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Clear DTCs

(c) Recheck for DTCs.

Click here

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes

HINT:

  • DTC C1A50 is stored when a malfunction signal sent from the electronically controlled brake system is detected.
  • If the malfunctioning part has been repaired or replaced before rechecking for DTCs, DTC C1A50 will not be output again.
  • If DTC C1A50 is output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even though the DTC was not output when rechecking for DTCs.

    Click here

Result

Proceed to

DTC C1A50 is output

A

DTC C1A50 is not output

B

A

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM

B

USE SIMULATION METHOD TO CHECK

READ NEXT:

 Steering Angle Midpoint Initial Setting Incomplete (C1AEA)

DESCRIPTION When the clearance warning ECU assembly detects that the steering angle neutral point memorization is incomplete during self-diagnosis, C1AEA is stored. DTC No. Detection Item DTC D

 ICS Detection Area Adjustment Incomplete (C1AF0)

DESCRIPTION When ICS detection area adjustment is incomplete, the clearance warning ECU assembly stores DTC C1AF0. DTC No. Detection Item DTC Detection Condition Trouble Area C1AF0 ICS

 Fr Sensor Initialization Incomplete (C1AF3)

DESCRIPTION When it is judged that the front sensors have not been initialized, the clearance warning ECU assembly stores DTC C1AF3. DTC No. Detection Item DTC Detection Condition Trouble Are

SEE MORE:

 Front Fog Light Circuit

DESCRIPTION Illumination of the front fog lights is controlled by the main body ECU (multiplex network body ECU). WIRING DIAGRAM except Sport Package: for Sport Package: CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the following inspect

 Short in Side Squib (RH) Circuit (B1820-B1823)

DESCRIPTION The front side squib RH circuit consists of the airbag ECU assembly and front seat airbag assembly RH. This circuit instructs the SRS to deploy when deployment conditions are met. These DTCs are stored when a malfunction is detected in the front side squib RH circuit. DTC No. Detect

© 2016-2025 Copyright www.lexunx.com