Lexus NX: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE PRE-COLLISION SYSTEM
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Make a note of the current settings before customizing.
(a) Customizing with the multi-information display
HINT:
The following PCS functions and the pre-collision system sensitivity setting can be changed from their default setting.
(1) Turn the power switch on (IG).
(2) Change pre-collision system settings by operating steering pad switch.
Settings| Customize Setting | Description | Default | Setting |
|---|---|---|---|
| PCS | Function that turns the pre-collision system on or off | On | On or Off |
| Sensitivity | Function that selects the warning sensitivity of the pre-collision function | Middle | Early, Middle or Late |
(b) Customizing with the Techstream
(1) Connect the Techstream to the DLC3.
(2) Turn the power switch on (IG).
(3) Turn the Techstream on.
(4) Enter the following menus: Customize Setting / Others.
(5) Select the setting by referring to the table below.
Others| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| PCS Function ON/OFF State Stored | Refer to the table below | Not Stored | $00:Not Stored,$01:Stored | Forward recognition camera |
| PCS Warning Timing State Stored 1 | Refer to the table below | Stored | $00:Not Stored,$01:Stored | Forward recognition camera |
| PCS Warning Timing State Stored 2 | Refer to the table below | Not Stored | $00:Not Stored,$01:Stored | Forward recognition camera |
| PCS Warning Timing State Stored 3 | Refer to the table below | Not Stored | $00:Not Stored,$01:Stored | Forward recognition camera |
| Customize Setting | Description | Setting |
|---|---|---|
| PCS Function ON/OFF State Stored | Function to maintain the pre-collision system on/off setting when the power switch is turned on (IG) from off with the pre-collision function off. | Not stored: Pre-collision system always turns on Stored: Pre-collision system maintains off |
| PCS Warning Timing State Stored 1 | Function to set whether or not to store the warning sensitivity setting when the PCS function is on and the power switch is turned from off to on (IG). | Not stored: Sensitivity and CAUTION is reset to default setting Stored: Sensitivity and CAUTION settings are maintained as previous value |
| PCS Warning Timing State Stored 2 | Function to set whether or not to store the warning sensitivity setting when the PCS function is off and the power switch is turned from off to on (IG). | Not stored: Sensitivity and CAUTION is reset to default setting Stored: Sensitivity and CAUTION settings are maintained as previous value |
| PCS Warning Timing State Stored 3 | Function to set whether or not to store the warning sensitivity setting when the PCS function is turned from off to on while the power switch is turned on (IG). | Not stored: Sensitivity and CAUTION is reset to default setting Stored: Sensitivity and CAUTION settings are maintained as previous value |
READ NEXT:
Initialization
INITIALIZATION STEERING SENSOR ZERO POINT CALIBRATION (a) Start the hybrid system. (b) Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (c) Turn the power switch off
Utility
UTILITY NOTICE: If any of the following parts has been replaced due to pre-collision system malfunction, those systems using those parts may be affected without performing necessary operations.
For
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE NOTICE: When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the info
SEE MORE:
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE NOTICE:
The following inspection procedures for the parking assist monitor system are based on the assumption that the navigation system is normal. If the navigation system has any malfunctions, first proceed with troubleshooting the navigation system.
Click here
Depend
Transmission Control Switch Circuit
DESCRIPTION When the shift lever is in S, different ranges can be chosen using the floor shift sequential gate. WIRING DIAGRAM PROCEDURE 1. READ VALUE USING TECHSTREAM (SPORTS MODE) (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Enter the following menus: Po
