Lexus NX: Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE INTELLIGENT CLEARANCE SONAR SYSTEM

(a) Customizing with the Techstream.

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

(1) Connect the Techstream to the DLC3.

(2) Turn the power switch on (IG).

(3) Turn the Techstream on.

(4) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Utility / Customize Setting.

(5) Select the setting by referring to the table below.

Warning

Tester Display

Description

Default

Setting

ECU

Fr Corner Sensor Onset Range

Sets the detection operation range for the front corner sensors.

Long

0:Short,1:Long

Clearance warning ECU assembly

Rr Corner Sensor Onset Range

Sets the detection operation range for the rear corner sensors.

Long

0:Short,1:Long

Clearance warning ECU assembly

Fr Sensor Onset Range

Sets the detection operation range for the front center sensors.

Wide

0:Narrow,1:Wide

Clearance warning ECU assembly

Rr Sensor Onset Range

Sets the detection operation range for the rear center sensors.

Wide

0:Narrow,1:Wide

Clearance warning ECU assembly

Fr & Rr Buzzer Volume

Changes the buzzer volume setting.

M

01:L,10:M,11:H

Clearance warning ECU assembly

Intuitive P/A Judgement of Obstacle on Course

Sets the availability of judgement of obstacle on course.

Valid

0:Valid,1:Invalid

Clearance warning ECU assembly

Sensor

Tester Display

Description

Default

Setting

ECU

Sensor Condition N

Makes the front sensors available when shift lever is in N.

Avail

0:Not Avail,1:Avail

Clearance warning ECU assembly

Display

Tester Display

Description

Default

Setting

ECU

Approach Display OFF

Sets whether the display turns off after an obstacle is no longer detected.

Avail

0:Not Avail,1:Avail

Clearance warning ECU assembly

Others

Tester Display

Description

Default

Setting

ECU

ICS Function

Intelligent clearance sonar system

ON

0:ON,1:OFF

Clearance warning ECU assembly

ICS SW Status Memory

Intelligent clearance sonar system main switch memory function

Yes

0:Yes,1:No

Clearance warning ECU assembly

ICS Stop Distance

Intelligent clearance sonar system target stopping distance

Long

0:Short,1:Long

Clearance warning ECU assembly

READ NEXT:

 Calibration

CALIBRATION NOTICE: When any of the following parts have been replaced, perform adjustment shown in the following table. If not, the intelligent clearance sonar system may not operate correctly. PRECA

 Utility

UTILITY FREEZE FRAME DATA NOTICE: Freeze frame data is stored and updated each time the brakes are operated. Only the latest 30 sets of data are stored. Using the Techstream, make sure to save th

 Problem Symptoms Table

PROBLEM SYMPTOMS TABLE NOTICE: When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the info

SEE MORE:

 On-vehicle Inspection

ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT RAIN SENSOR (a) Remove the rain sensor cover. Click here (b) Disconnect the rain sensor connector. *a Front view of wire harness connector (to Rain Sensor) (c) Measure the voltage according to the value(s) in the table below. St

 If a warning light turns on or a warning buzzer sounds

Calmly perform the following actions if any of the warning lights comes on or flashes. If a light comes on or flashes, but then goes off, this does not necessarily indicate a malfunction in the system. However, if this continues to occur, have the vehicle inspected by your Lexus dealer. Acti

© 2016-2025 Copyright www.lexunx.com