Lexus NX: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE INTUITIVE PARKING ASSIST SYSTEM
(a) Customizing with the Techstream.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(1) Connect the Techstream to the DLC3.
(2) Turn the power switch on (IG).
(3) Turn the intuitive parking assist system on.
(4) Turn the Techstream on.
(5) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Utility / Customize Setting.
(6) Select the setting by referring to the table below.
Warning| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Fr Corner Sensor Onset Range | Sets the detection operation range for the front corner sensors. | Long | 0:Short,1:Long | Clearance warning ECU assembly |
| Rr Corner Sensor Onset Range | Sets the detection operation range for the rear corner sensors. | Long | 0:Short,1:Long | Clearance warning ECU assembly |
| Fr Sensor Onset Range | Sets the detection operation range for the front center sensors. | Wide | 0:Narrow,1:Wide | Clearance warning ECU assembly |
| Rr Sensor Onset Range | Sets the detection operation range for the rear center sensors. | Wide | 0:Narrow,1:Wide | Clearance warning ECU assembly |
| Fr & Rr Buzzer Volume | Changes the buzzer volume setting. | M | 01:L,10:M,11:H | Clearance warning ECU assembly |
| Intuitive P/A Auto Mute Function | Sets the availability of the auto mute function. | ON | 0:ON,1:OFF | Clearance warning ECU assembly |
| Intuitive P/A Judgement of Obstacle on Course | Sets the availability of judgement of obstacle on course. | Valid | 0:Valid,1:Invalid | Clearance warning ECU assembly |
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Sensor Condition N | Makes the front sensors available when the shift lever is in N. | Avail | 0:Not Avail,1:Avail | Clearance warning ECU assembly |
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Approach Display OFF | Sets whether the display turns off after an obstacle is no longer detected. | Avail | 0:Not Avail,1:Avail | Clearance warning ECU assembly |
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Intuitive P/A Switch State Stored | Sets the availability of the clearance sonar switch state stored function. | Stored | 0:Not Stored,1:Stored | Clearance warning ECU assembly |
(b) Customizing with multi information display
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(1) Turn the power switch on (IG).
(2) Turn the intuitive parking assist system on.
(3) Enter the following menus: Setting / Vehicle Setting / Parking assist.
(4) Select the setting by referring to the table below.
Intuitive parking assist Setting| Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Volume | Sets the buzzer alert volume. | 2 | 1, 2 or 3 | Clearance warning ECU assembly |
READ NEXT:
Calibration
CALIBRATION NOTICE: When any of the following parts have been replaced, perform adjustment shown in the following table. If not, the intuitive parking assist system may not operate correctly. ADJUST I
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of p
Terminals Of Ecu
TERMINALS OF ECU CLEARANCE WARNING ECU ASSEMBLY (a) Disconnect the I20 clearance warning ECU assembly connector. (b) Measure the voltage and resistance on the wire harness side connector according to
SEE MORE:
Front Camera Current Malfunction (C1682)
DESCRIPTION This DTC is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the parking assist ECU. DTC No. Detection Item DTC Detection Condition Trouble Area C168
Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PROCEDURE 1. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY NOTICE: Do not touch the cone part of the speaker. (a) Connect the connector and insert the 2 protrusion
