Lexus NX: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / SRS Airbag, Combination Meter or Occupant Detection / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > SRS Airbag > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Left side Buckle SW | Driver side buckle switch | Unset, Set or NG | Unset: Seat belt not fastened Set: Seat belt fastened NG: Data is not determined | - |
| Right side Buckle SW | Front passenger side buckle switch | Unset, Set or NG | Unset: Seat belt not fastened Set: Seat belt fastened NG: Data is not determined | Perform the inspection while sitting in the front passenger side seat. |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Driver Side Seatbelt Warning Buzzer | Driver side seat belt warning buzzer | ON or OFF | Customized value displayed | - |
| P-Seatbelt Warning Buzzer | Front passenger side seat belt warning buzzer | ON or OFF | Customized value displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Passenger Buckle SW | Front passenger side buckle switch | Set, Unset or NG | Unset: Seat belt not fastened Set: Seat belt fastened NG: Data is not determined | Perform the inspection while sitting in the front passenger side seat. |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Combination Meter > Active Test| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Front seat belt warning light | OFF/ON | - |
READ NEXT:
Driver Side Seat Belt Warning Light does not Operate
DESCRIPTION The combination meter assembly illuminates, blinks or turns off the front seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner bel
Front Passenger Side Seat Belt Warning Light Malfunction
DESCRIPTION When the power switch is turned on (IG), the occupant detection ECU sends a signal to the airbag ECU assembly to indicate the state of the front seat inner belt assembly RH and also whethe
Rear Seat Belt Warning Light Malfunction
DESCRIPTION The main body ECU (multiplex network body ECU) detects whether either rear door is open or closed based on the condition of the left and right courtesy light switches and then sends the re
SEE MORE:
Drive Motor "A" Control Module (P0A1B-505,P0A1B-806)
DTC SUMMARY MALFUNCTION DESCRIPTION These DTCs indicate that a large current flowed in the inverter for the motor. The cause of this malfunction may be one of the following: Internal inverter malfunction
Internal circuit malfunction in the inverter for the motor
Malfunction in ECU that controls
Dtc Check / Clear
DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Smart Access / Trouble Codes. Body Electrical > Smart Access > Trouble Codes (e) Check the details of the DTCs. Cl
