Lexus NX manuals

Lexus NX: Front Passenger Side Door Entry Lock Function does not Operate

Lexus NX Service Manual / Vehicle Interior / Theft Deterrent / Keyless Entry / Smart Access System With Push-button Start (for Entry Function) / Front Passenger Side Door Entry Lock Function does not Operate

DESCRIPTION

If the entry lock function does not operate for the front passenger door only, but the entry unlock function operates, the request code is being transmitted properly from the for passenger door. In this case, there may be a problem related to the lock sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door)).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • The smart access system with push-button start (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart access system with push-button start (for Entry Function) after confirming that the communication systems are functioning properly.

    Click here

  • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  • Before replacing the certification ECU (smart key ECU assembly), refer to smart access system with push-button start (for Entry Function) Precaution.

    Click here

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE

1.

CHECK POWER DOOR LOCK CONTROL SYSTEM

(a) When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click here

OK:

Door locks operate normally.

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM

OK

2.

READ VALUE USING TECHSTREAM (P-DOOR TRIGGER SWITCH)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Access / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Access > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

P-Door Trigger Switch

Front passenger door touch sensor (lock sensor)

ON or OFF

ON: Front passenger door touch sensor (lock sensor) touched

OFF: Front passenger door touch sensor (lock sensor) not touched
  • Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
  • Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
Body Electrical > Smart Access > Data List

Tester Display

P-Door Trigger Switch

HINT:

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.

OK:

The Techstream display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door).

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

(a) Disconnect the I53 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the L4 front door outside handle assembly (for front passenger door) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I53-2 (CLG2) - L4-4 (ANT1)

Always

Below 1 Ω

I53-1 (CG2B) - L4-5 (ANT2)

Always

Below 1 Ω

I53-2 (CLG2) or L4-4 (ANT1) - Body ground

Always

10 kΩ or higher

I53-1 (CG2B) or L4-5 (ANT2) - Body ground

Always

10 kΩ or higher

(d) Reconnect the L4 front door outside handle assembly (for front passenger door) connector.

(e) Reconnect the I53 certification ECU (smart key ECU assembly) connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

4.

CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (INPUT TO FRONT PASSENGER DOOR LOCK SENSOR)

*a

Component with harness connected

(Certification ECU (Smart Key ECU Assembly))

*b

Waveform 1

*c

Lock sensor not touched

*d

Lock sensor touched

(a) Using an oscilloscope, check the waveform.

OK:

Tester Connection

Condition

Tool Setting

Specified Condition

I53-2 (CLG2) - I53-11 (E)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly brought outside vehicle
  3. All doors closed
  4. All doors locked through wireless operation

    (electrical key transmitter sub-assembly brought outside detection area*)

  5. Front passenger door lock sensor touched

5 V/DIV., 40 ms/DIV.

Pulse generation

(See waveform 1)

*: For details about the entry function detection area, refer to Operation Check.

Click here

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

READ NEXT:

 Rear Door LH Entry Lock Function does not Operate

DESCRIPTION If the entry lock function does not operate for the rear door LH only, but the entry unlock function operates, the request code is being transmitted properly from the rear door LH. In this

 Rear Door RH Entry Lock Function does not Operate

DESCRIPTION If the entry lock function does not operate for the rear door RH only, but the entry unlock function operates, the request code is being transmitted properly from the for rear door RH. In

 Room Oscillator does not Recognize Key

DESCRIPTION If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (No. 1 indoor electrical key antenna assembly (front floo

SEE MORE:

 Lost Communication With Multi-axis Acceleration Sensor Module Missing Message (U012587,U012687,U012987,U013187,U015587,U029387)

DESCRIPTION When a malfunction is detected between various ECUs and sensors, these DTCs are stored. DTC No. Detection Item DTC Detection Condition Trouble Area U012587 Lost Communication With Multi-axis Acceleration Sensor Module Missing Message 3 seconds after the power switch is t

 Components

COMPONENTS ILLUSTRATION *1 DECK FLOOR BOX LH *2 NO. 3 DECK BOARD SUB-ASSEMBLY *3 REAR DECK FLOOR BOX *4 NEGATIVE AUXILIARY BATTERY TERMINAL N*m (kgf*cm, ft.*lbf): Specified torque - - ILLUSTRATION *1 BRAKE PEDAL PAD *2 BRAKE PEDAL RETURN SPRING *3 BR

© 2016-2024 Copyright www.lexunx.com