Lexus NX: Glass Surroundings Temperature Sensor Circuit (B14A9)
DESCRIPTION
The air conditioning amplifier assembly detects the temperature of the area near the windshield glass using this circuit. The air conditioning amplifier assembly applies voltage to the air conditioning thermistor assembly (glass surroundings temperature sensor). As the temperature of the area near the windshield glass rises, the resistance decreases. The air conditioning amplifier assembly detects the change in resistance as the windshield glass surroundings temperature changes.
The glass surroundings temperature sensor is integrated with the air conditioning thermistor assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B14A9 | Glass Surroundings Temperature Sensor Circuit | Open or short in glass surroundings temperature sensor circuit |
| Memorized (4 seconds or more)* | - |
- *: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
WIRING DIAGRAM
.png)
CAUTION / NOTICE / HINT
HINT:
The air conditioning thermistor assembly must be replaced if the glass surroundings temperature sensor is malfunctioning.
PROCEDURE
| 1. | READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Air Conditioner / Data List.
(e) Check the value(s) by referring to the table below.
Body Electrical > Air Conditioner > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Glass Surroundings Temperature | Glass surroundings temperature | Min.: -327.68°C (-557.82°F) Max.: 327.67°C (621.81°F) | Actual glass surroundings temperature is displayed | - |
| Tester Display |
|---|
| Glass Surroundings Temperature |
OK:
The display is as specified in the normal condition column.
| OK | .gif) | REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
|
.gif)
| 2. | INSPECT AIR CONDITIONING THERMISTOR ASSEMBLY (GLASS SURROUNDINGS TEMPERATURE SENSOR) |
(a) Remove the air conditioning thermistor assembly (glass surroundings temperature sensor).
Click here .gif)
(b) Inspect the air conditioning thermistor assembly (glass surroundings temperature sensor).
Click here
| NG | | REPLACE AIR CONDITIONING THERMISTOR ASSEMBLY (GLASS SURROUNDINGS TEMPERATURE SENSOR) |
|
| 3. | CHECK HARNESS AND CONNECTOR (AIR CONDITIONING THERMISTOR ASSEMBLY [GLASS SURROUNDINGS TEMPERATURE SENSOR] - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
(a) Disconnect the T13 air conditioning thermistor assembly (glass surrounding temperature sensor).
(b) Disconnect the I50 air conditioning amplifier assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T13-2 (TNG) - I50-6 (TNG) | Always | Below 1 Ω |
| T13-1 (SEG3) - I50-35 (SG-5) | Always | Below 1 Ω |
| T13-2 (TNG) or I50-6 (TNG) - Body ground | Always | 10 kΩ or higher |
| T13-1 (SEG3) or I50-35 (SG-5) - Body ground | Always | 10 kΩ or higher |
| OK | | REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
Glass Humidity Sensor Circuit (B14AA)
DESCRIPTION The air conditioning thermistor assembly (glass humidity sensor) detects cabin humidity. The voltage of the air conditioning thermistor assembly (glass humidity sensor) changes in accordan
Lost Communication with Front Panel LIN (B14B2)
DESCRIPTION The air conditioning control assembly communicates with the air conditioning amplifier assembly through the LIN communication system. If the LIN communication system malfunctions, the air
Refrigerant Shortage (B14B8)
DESCRIPTION This DTC is stored if the amount of refrigerant in the air conditioning system is insufficient. The air conditioning amplifier assembly receives the ambient temperature signal, refrigerant
SEE MORE:
Inspection
INSPECTION PROCEDURE 1. INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY (BRAKE HOLD SWITCH) (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 8 (SLT1) - 16 (GND1) Switch not pushed 1 MΩ or
On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT HINT:
Water Pump Construction Evaporation Port and Drain Plug: *1 Evaporation Port *2 Mechanical Seal *3 Fluid Catch Pocket *4 Drain Plug *a Typical Water Pump Assembly - -
Water Pump Mechanical Seal
The water pum
