Lexus NX: Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH
(a) Check that the power switch is off.
(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Attach the guide and hold the side airbag sensor assembly LH in place.
(d) Install the nut.
Torque:
9.0 N·m {92 kgf·cm, 80 in·lbf}
NOTICE:
- If the side airbag sensor assembly LH has been dropped, replace it with a new one.
- When installing the side airbag sensor assembly LH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
- Tighten the nut while holding the side airbag sensor assembly LH because the side airbag sensor assembly LH guide is easily damaged.
(e) Before connecting the airbag connector, check that the position of the housing lock is correct as shown in the illustration.
| *a | Correct | *b | Incorrect |
(f) Connect the airbag connector.
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
(1) While holding the CPA, be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).
NOTICE:
Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.
| *1 | CPA | - | - |
| *a | CPA Upper Part | - | - |
(g) Check that there is no looseness in the installation parts of the side airbag sensor assembly LH.
2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Click here .gif)
3. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Click here
4. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY
Click here
5. INSTALL ROPE HOOK ASSEMBLY
Click here
6. INSTALL UPPER DECK TRIM SIDE BOARD LH
Click here
7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
8. INSTALL REAR FLOOR FINISH PLATE
Click here
9. INSTALL SPARE TIRE
Click here
10. INSTALL REAR SEAT ASSEMBLY (for Manual Seat)
Click here
11. INSTALL REAR SEAT ASSEMBLY (for Power Seat)
Click here
12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
(a) Connect the cable to the negative (-) auxiliary battery terminal and tighten the nut.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
13. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click here
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
14. INSTALL DECK FLOOR BOX LH
Click here
15. INSTALL REAR DECK FLOOR BOX
Click here
16. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
Click here
17. PERFORM DIAGNOSTIC SYSTEM CHECK
Click here
18. CHECK SRS WARNING LIGHT
Click here
READ NEXT:
Components
COMPONENTS ILLUSTRATION *1 DECK FLOOR BOX LH *2 NO. 3 DECK BOARD SUB-ASSEMBLY *3 REAR DECK FLOOR BOX *4 AUXILIARY BATTERY NEGATIVE TERMINAL N*m (kgf*cm, ft.*lbf): Specified
On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to follow the correct removal and installation procedures of the seat position airbag sensor. PROCEDURE 1. INSPECT SEAT POSITION AIRBAG S
SEE MORE:
Drive Motor "B" Inverter Performance (P0A79-696)
DTC SUMMARY MALFUNCTION DESCRIPTION This DTC indicates a malfunction inside the inverter for the rear motor. The cause of this malfunction may be one of the following: Area Main Malfunction Description Step Inverter low-voltage circuit The connectors are not connected properly 3 H
Components
COMPONENTS ILLUSTRATION *1 CONSOLE ARMREST ASSEMBLY *2 HEADUP DISPLAY SWITCH ASSEMBLY *3 INSTRUMENT SIDE PANEL LH *4 LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL *5 NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY *6 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY *7 N
