Lexus NX: Internal Control Module EEPROM Error (P062F-143,P062F-165)
DESCRIPTION
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P062F-143 | Internal Control Module EEPROM Error | ECU internal malfunction (EEPROM error) (1 trip detection logic) | Hybrid vehicle control ECU | Comes on | Master Warning Light: Comes on |
| P062F-165 | Internal Control Module EEPROM Error | ECU internal malfunction (EEPROM error) (1 trip detection logic) | Hybrid vehicle control ECU | Comes on | Master Warning Light: Comes on |
MONITOR DESCRIPTION
The hybrid vehicle control ECU monitors its internal operation. If the internal operation is malfunctioning, the hybrid vehicle control ECU illuminates the MIL and stores a DTC.
MONITOR STRATEGY
| Related DTCs | P062F (INF 143): Internal control module EEPROM P062F (INF 165): Internal control module EEPROM for battery data |
| Required sensors/components | Hybrid vehicle control ECU |
| Frequency of operation | Continuous |
| Duration | TMC's intellectual property |
| MIL operation | 1 driving cycle / Immediately |
| Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
| The monitor will run whenever the following DTCs are not stored | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
TYPICAL MALFUNCTION THRESHOLDS
| TMC's intellectual property | - |
COMPONENT OPERATING RANGE
| Hybrid vehicle control ECU | DTC P062F (INF 143/165) is not detected |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 30 seconds or more.
- Turn the power switch on (IG) and wait for 15 seconds or more, turn the power switch off. [A]
- Repeat [A] 3 times. [B]
- Turn the power switch on (IG) and turn the Techstream on.
- Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. [C]
-
Read the current DTCs.
HINT:
- If a current DTC is output, the system is malfunctioning.
- If current DTCs are not output, perform the following steps to check for permanent DTCs.
- Check that the permanent DTCs are cleared.
- If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.
CAUTION / NOTICE / HINT
NOTICE:
There is a possibility that the DTC P062F is issued from the ECUs of the ECM and hybrid vehicle control ECU. Use Techstream to conduct a health check to confirm which ECU the DTC is issued from and then inspect the related system.
HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
- Turn the power switch off and wait for 30 seconds or more.
- Turn the power switch on (IG) and wait for 15 seconds or more.
PROCEDURE
| 1. | REPLACE HYBRID VEHICLE CONTROL ECU |
Click here .gif)
| NEXT | .gif) | COMPLETED |
READ NEXT:
Internal Control Module EEPROM Error (P062F-489)
DESCRIPTION The hybrid vehicle control ECU monitors its internal operation and will store the DTC when it detects an internal malfunction. DTC No. Detection Item DTC Detection Condition Troub
Sensor Power Supply "A" Circuit / Open (P06B0-163,P06D6-511,P06E6-164,P0A1B-786,P0A1B-794,P1C2B-192,P1C73-512,P1CA7-193,P3134-661)
DESCRIPTION The MG ECU, which is built into the inverter with converter assembly, monitors its internal operation and will store DTCs if the system is malfunctioning. If any of the following DTCs are
Transmission Range Sensor Circuit (P0705-757)
DESCRIPTION The shift lever position sensor sends 7 different switch signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses these signals to detect the shift lever position (P,
SEE MORE:
Installation
INSTALLATION PROCEDURE 1. INSTALL SHIFT LEVER POSITION SENSOR (a) Install the shift lever position sensor to the manual valve shaft. (b) Temporarily install the 2 bolts. (c) Install the lock plate and tighten the lock nut. Torque: 6.9 N·m {70 kgf·cm, 61 in·lbf} (d) Temporarily install the contro
Main Microcomputer in Front Radar Sensor Calibration/Parameter Memory Failure (C1A8C46,C1A8D1C,C1A9000,C1A9100)
DESCRIPTION When an internal malfunction is detected in the millimeter wave radar sensor assembly, a DTC is stored. DTC No. Detection Item DTC Detection Condition Trouble Area C1A8C46 Main Microcomputer in Front Radar Sensor Calibration/Parameter Memory Failure When the power switch
