Lexus NX: Power Retractable Mirrors do not Operate with Power Retract Mirror Switch
DESCRIPTION
When the outer mirror switch assembly mirror retract switch is operated, deploy/retract signals are sent to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) sends deploy/retract signals to the outer mirror control ECU assembly via CAN communication. The outer mirror control ECU assembly deploys and retracts the outer rear view mirror assembly based on the received signals.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.
Click here
.gif)
-
If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.
Click here
PROCEDURE
| 1. | READ VALUE USING TECHSTREAM (OUTER MIRROR FOLD SW) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Outer Mirror Fold SW | Mirror retract switch signal | OFF or ON | OFF: Mirror retract switch not in retract position ON: Mirror retract switch in retract position | - |
| Tester Display |
|---|
| Outer Mirror Fold SW |
OK:
On the Techstream screen, ON or OFF is displayed for each item according to the table above.
| NG | .gif) | GO TO STEP 5 |
|
.gif)
| 2. | CHECK MALFUNCTIONING PARTS |
(a) Check the malfunctioning parts.
Click here
| Result | Proceed to |
|---|---|
| Both mirrors are malfunctioning | A |
| LH side mirror is malfunctioning | B |
| RH side mirror is malfunctioning | C |
| A | | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| C | | GO TO STEP 4 |
|
| 3. | INSPECT OUTER MIRROR RETRACTOR LH (POWER RETRACT FUNCTION) |
(a) Remove the outer rear view mirror assembly LH.
Click here
(b) Inspect the outer mirror retractor LH.
Click here
| OK | | REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH |
| NG | | REPLACE OUTER MIRROR RETRACTOR LH |
| 4. | INSPECT OUTER MIRROR RETRACTOR RH (POWER RETRACT FUNCTION) |
(a) Remove the outer rear view mirror assembly RH.
Click here
(b) Inspect the outer mirror retractor RH.
Click here
| OK | | REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH |
| NG | | REPLACE OUTER MIRROR RETRACTOR RH |
| 5. | INSPECT OUTER MIRROR SWITCH ASSEMBLY (MIRROR RETRACT SWITCH) |
(a) Remove the outer mirror switch assembly.
Click here
(b) Inspect the outer mirror switch assembly.
Click here
| NG | | REPLACE OUTER MIRROR SWITCH ASSEMBLY |
|
| 6. | CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND) |
(a) Disconnect the M13 outer mirror switch assembly connector.
(b) Disconnect the I47 main body ECU (multiplex network body ECU) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M13-8 (MR) - I47-15 (RTR) | Always | Below 1 Ω |
| M13-11 (MF) - I47-14 (RET) | Always | Below 1 Ω |
| M13-10 (E) - Body ground | Always | Below 1 Ω |
| M13-8 (MR) or I47-15 (RTR) - Body ground | Always | 10 kΩ or higher |
| M13-11 (MF) or I47-14 (RET) - Body ground | Always | 10 kΩ or higher |
| OK | | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
AUTO Power Retract Mirrors do not operate
DESCRIPTION When the outer mirror switch assembly is set to AUTO (neutral position), an AUTO signal is detected by the main body ECU (multiplex network body ECU). When locking and unlocking all doors
Power Mirror Surface Position is not Memorized
DESCRIPTION When the seat memory switch is operated, the switch input signal is sent via CAN communication from the outer mirror control ECU assembly LH to the main body ECU (multiplex network body EC
Reverse Shift-linked Function of Power Mirrors does not Operate
DESCRIPTION Hybrid vehicle control ECU sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex
SEE MORE:
Dtc Check / Clear
DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Telematics / Trouble Codes. Body Electrical > Telematics > Trouble Codes (e) Check for DTCs. Click here CLEAR DT
USB Audio System Recognition/Play Error
DESCRIPTION When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio receiver assembly. This diagnosis procedure is for when a device is not recognized, or fil
