Lexus NX manuals

Lexus NX: Registration

Lexus NX Service Manual / Vehicle Interior / Theft Deterrent / Keyless Entry / Immobiliser System / Registration

REGISTRATION

PROCEDURE

1. INSTALL CAUTION REGARDING INTERFERENCE WITH ELECTRONIC DEVICES

CAUTION:

  • People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should keep away from the smart key system antennas. The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your dealer for details, such as the frequency of radio waves and timing of the emitted radio waves. Then, consult your doctor to see if you should disable the entry function.
  • User of any electrical medical device other than implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.
  • Ask your dealer for details for disabling the entry function.

2. DESCRIPTION OF CODE REGISTRATION

HINT:

  • The electrical key transmitter sub-assembly (for card type) can be registered using the same procedure as the electrical key transmitter sub-assembly (for standard type).
  • Registering an ID code enables the smart access system with push-button start function, wireless door lock control function and immobiliser function to be operated.
  • Code registration is needed when the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU), main body ECU (multiplex network body ECU), steering lock ECU (steering lock actuator assembly) or electrical key transmitter sub-assembly is replaced with a new one.
  • This vehicle does not have a key slot. Therefore, while facing the logo side of the electrical key transmitter sub-assembly towards the power switch, hold the transmitter near the power switch as shown in the illustration to register the electrical key transmitter sub-assembly.

*A

for Standard Type

*B

for Card Type

*C

w/ Power Back Door System

*1

Power Switch

*2

Electrical Key Transmitter Sub-assembly

3. KEY REGISTRATION PROCEDURES WHEN ADDING OR REPLACING KEY OR WHEN KEY IS LOST

HINT:

  • The following procedures require the use of the Techstream:
    • - New key ID registration
    • - Additional key ID registration
    • - Key ID erasure
    • - All Keys ID erasure
  • A maximum of 7 electrical key transmitter sub-assemblies can be registered (this includes any electrical key transmitter sub-assemblies registered when the vehicle was purchased).
  • In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate step numbers. Perform the steps in numerical order.

Customer Request/Condition

Registration Procedure Condition

Procedure

Refer to

Registering additional electrical key transmitter sub-assembly

Customer must bring at least 1 electrical key transmitter sub-assembly

1. Register additional electrical key transmitter sub-assemblies as necessary (additional key ID registration)

PROCEDURE "C"
  • Replacing an electrical key transmitter sub-assembly (e.g., when replacing an old electrical key transmitter sub-assembly with a new one)
  • Making a lost electrical key transmitter sub-assembly unusable

NOTICE:

If the customer brings at least 1 electrical key transmitter sub-assembly, it is possible to perform these procedures. However, if any additional electrical key transmitter sub-assemblies are registered before reregistering the customer's electrical key transmitter sub-assemblies, the customer's electrical key transmitter sub-assemblies cannot be reregistered and become useless. Therefore, if the customer does not bring all of their electrical key transmitter sub-assemblies, be sure to explain to them that any electrical key transmitter sub-assemblies not brought will become useless after additional electrical key transmitter sub-assemblies are registered.

HINT:

After electrical key transmitter sub-assembly ID erasure, any remaining electrical key transmitter sub-assemblies that are not reregistered at this time cannot be used. Therefore, immediately after electrical key transmitter sub-assembly ID erasure, be sure to reregister all available remaining electrical key transmitter sub-assemblies.

Customer must bring at least 1 electrical key transmitter sub-assembly

1. Using remaining electrical key transmitter sub-assembly, clear all registered electrical key transmitter sub-assemblies except one (key ID erasure)

PROCEDURE "D"

2. Register additional electrical key transmitter sub-assemblies as necessary (additional key ID registration)

PROCEDURE "C"

All electrical key transmitter sub-assemblies are lost

-

1. Reset all electrical key transmitter sub-assemblies (all keys ID erasure (key code reset))

PROCEDURE "E"

2. Register all electrical key transmitter sub-assemblies (new key ID registration)

PROCEDURE "A"

4. PART REPLACEMENT AND REGISTRATION PROCEDURES

(a) If a malfunctioning ECU is discovered through troubleshooting of the smart access system with push-button start, use the ECU replacement and electrical key transmitter sub-assembly registration procedures in the table below.

NOTICE:

Do not use a main body ECU (multiplex network body ECU) and DCM (telematics transceiver)* that has been registered to another vehicle.

  • *: for Lexus Enform Remote Compatible Type

HINT:

  • The following procedures require the use of the Techstream:
    • - New key ID registration
    • - Additional key ID registration
    • - Key ID erasure
    • - ECU code registration
  • A maximum of 7 electrical key transmitter sub-assemblies can be registered (this includes any electrical key transmitter sub-assemblies registered when the vehicle was purchased).
  • Immediately after replacing the certification ECU (smart key ECU assembly), the Techstream item "A number of registered codes" should change to "0". If this item does not change to "0", the certification ECU (smart key ECU assembly) may be registered to another vehicle. A certification ECU (smart key ECU assembly) which is registered to another vehicle cannot be used.
  • In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate step numbers. Perform the steps in numerical order.

Malfunctioning ECU

Condition

Procedure

Refer to

Certification ECU (smart key ECU assembly)

Customer has brought all electrical key transmitter sub-assemblies

1. Replace certification ECU (smart key ECU assembly)

-

2. Reregister all of the customer's electrical key transmitter sub-assemblies

PROCEDURE "B"*1

3. Perform remote engine start and stop registration*2

PROCEDURE "I"

Some electrical key transmitter sub-assemblies are lost

Key ID codes can be registered and cleared

1. Clear key codes (key ID erasure)

PROCEDURE "D"

2. Perform additional electrical key transmitter sub-assembly registration procedure (additional key ID registration)

HINT:

  • If some electrical key transmitter sub-assemblies are not registered during above step, they will be disabled because they cannot be registered later.
  • Purpose is to clear electrical key transmitter sub-assembly information stored in ID code box (immobiliser code ECU) for any electrical key transmitter sub-assemblies that user did not bring. If this information is not cleared, when certification ECU (smart key ECU assembly) is replaced and electrical key transmitter sub-assembly registration is performed, electrical key transmitter sub-assembly information stored in certification ECU (smart key ECU assembly) and electrical key transmitter sub-assembly information stored in ID code box (immobiliser code ECU) will not match and hybrid control system cannot be started.

PROCEDURE "C"*1

3. Replace certification ECU (smart key ECU assembly)

-

4. Reregister all electrical key transmitter sub-assemblies

PROCEDURE "B"

5. Perform remote engine start and stop registration*2

PROCEDURE "I"

Key ID codes cannot be either registered or cleared

1. Replace certification ECU (smart key ECU assembly)

-

2. Replace ID code box (immobiliser code ECU)

-

3. Reregister all electrical key transmitter sub-assemblies (new key ID registration)

HINT:

If some electrical key transmitter sub-assemblies are not registered during above step, they will be disabled because they cannot be registered later.

PROCEDURE "A"

4. ECU communication ID registration

PROCEDURE "G"

5. Perform remote engine start and stop registration*2

PROCEDURE "I"

Certification ECU (smart key ECU assembly)

All electrical key transmitter sub-assemblies are lost

1. Replace certification ECU (smart key ECU assembly)

-

2. Replace ID code box (immobiliser code ECU)

-

3. Register all electrical key transmitter sub-assemblies (new key ID registration)

PROCEDURE "A"

4. ECU communication ID registration

PROCEDURE "G"

5. Perform remote engine start and stop registration*2

PROCEDURE "I"

ID code box (immobiliser code ECU)

Customer has brought at least 1 electrical key transmitter sub-assembly

1. Replace ID code box (immobiliser code ECU)

-

2. Register recognition codes in ECUs (ECU code registration)

PROCEDURE "F"

3. ECU communication ID registration

PROCEDURE "G"

All electrical key transmitter sub-assemblies are lost

1. Replace certification ECU (smart key ECU assembly)

-

2. Replace ID code box (immobiliser code ECU)

-

3. Register all electrical key transmitter sub-assemblies (new key ID registration)

HINT:

If some electrical key transmitter sub-assemblies are not registered during above steps, they will be disabled because they cannot be registered later

PROCEDURE "A"

4. ECU communication ID registration

PROCEDURE "G"

5. Perform remote engine start and stop registration*2

PROCEDURE "I"

Steering lock ECU (steering lock actuator assembly)

Customer has brought at least 1 electrical key transmitter sub-assembly

1. Replace steering lock ECU (steering lock actuator assembly)

-

2. Register recognition codes in ECUs (ECU code registration)

PROCEDURE "F"

All electrical key transmitter sub-assemblies are lost

1. Replace certification ECU (smart key ECU assembly)

-

2. Replace ID code box (immobiliser code ECU)

-

3. Replace steering lock ECU (steering lock actuator assembly)

-

4. Register all electrical key transmitter sub-assemblies (new key ID registration)

PROCEDURE "A"

5. ECU communication ID registration

PROCEDURE "G"

6. Perform remote engine start and stop registration*2

PROCEDURE "I"

Hybrid vehicle control ECU

When replacing the hybrid vehicle control ECU with a new one

Replace hybrid vehicle control ECU

-

When replacing the hybrid vehicle control ECU with a used one

1. Replace hybrid vehicle control ECU

-

2. ECU communication ID registration

PROCEDURE "G"

Main body ECU (multiplex network body ECU)

When using a new one

1. Replace main body ECU (multiplex network body ECU)

-

2. Register recognition codes in ECUs (ECU code registration)

PROCEDURE "F"

3. Perform remote door lock and unlock registration*2

PROCEDURE "H"

When not using a new one

NOTICE:

Do not use a main body ECU (multiplex network body ECU) that has been registered to another vehicle.

-

DCM (telematics transceiver)*2

When replacing the DCM (telematics transceiver) with a new one

1. Replace DCM (telematics transceiver)

-

2. Perform remote door lock and unlock registration

PROCEDURE "H"

3. Perform remote engine start and stop registration

PROCEDURE "I"

When replacing the DCM (telematics transceiver) with a used one

NOTICE:

Do not use a DCM (telematics transceiver) that has been registered to another vehicle.

-
  • *1: It is only necessary to perform processes 1 through 3.
  • *2: for Lexus Enform Remote Compatible Type

5. KEY REGISTRATION (PROCEDURE "A")

(a) New key ID registration:

HINT:

In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate step numbers. Perform the steps in numerical order.

Process

Procedure

1. Start of registration
  1. Prepare all new electrical key transmitter sub-assemblies to be registered and place them outside vehicle. Bring 1 new electrical key transmitter sub-assembly inside vehicle.
  2. Connect the Techstream to DLC3
  3. While holding new electrical key transmitter sub-assembly, turn power switch on (IG)

    HINT:

    Power switch cannot be turned on (IG) more than 10 times. To continue electrical key transmitter sub-assembly registration procedure with power switch off, use either method below:

    • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
    • Connect the Techstream to DLC3 and select "Manual" from initial screen on the Techstream. Then select "Key Code Registration" under model code.
  4. Turn the Techstream on
  5. Enter following menus: Body Electrical / Smart Access / Utility / Smart Code Registration

2. Confirmation of ECU code
  • Perform operation according to prompts on the Techstream screen

HINT:

Mode is automatically selected by the Techstream (new registration mode or add mode)

3. Verification of unregistered electrical key transmitter sub-assembly*
  1. While facing logo side of unregistered transmitter toward power switch, hold transmitter near power switch.
  2. Confirm that wireless door lock buzzer sounds twice (short beep)
  3. Bring electrical key transmitter sub-assembly for which operations have been completed outside vehicle. Then bring another new electrical key transmitter sub-assembly for which operations are to be performed into vehicle.

4. Registration of ID code
  • Perform operation according to prompts on the Techstream screen

5. End of registration
  • Finish new key ID code registration
  • *: Repeat this process for each electrical key transmitter sub-assembly which is to be registered to the vehicle. Finish the procedure for each electrical key transmitter sub-assembly within 30 seconds. If the procedure for any of the electrical key transmitter sub-assemblies is not finished within the specified time, perform the registration from process 1 again.
  • If "Smart Access System with Push-button Start" is canceled, registration cannot be performed.

    Click here

6. KEY REGISTRATION (PROCEDURE "B")

(a) New key ID registration:

HINT:

In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate step numbers. Perform the steps in numerical order.

Process

Procedure

1. Start of registration
  1. Prepare all registered electrical key transmitter sub-assemblies and any electrical key transmitter sub-assemblies to be registered and place them outside vehicle. Bring 1 registered electrical key transmitter sub-assembly inside vehicle.
  2. Connect the Techstream to DLC3
  3. While holding registered electrical key transmitter sub-assembly, turn power switch on (IG)

    HINT:

    Power switch cannot be turned on (IG) more than 10 times. To continue electrical key transmitter sub-assembly registration procedure with power switch off, use either method below:

    • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
    • Connect the Techstream to DLC3 and select "Manual" from initial screen on the Techstream. Then select "Key Code Registration" under model code.
  4. Turn the Techstream on
  5. Enter following menus: Body Electrical / Smart Access / Utility / Smart Code Registration

2. Confirmation of ECU code
  • Perform operation according to prompts on the Techstream screen

HINT:

Mode is automatically selected by the Techstream (new registration mode or add mode)

3. Confirmation of all registered electrical key transmitter sub-assemblies*1
  1. While facing logo side of registered transmitter toward power switch, hold transmitter near power switch.
  2. Confirm that wireless door lock buzzer sounds once (short beep)
  3. Bring electrical key transmitter sub-assembly for which operations have been completed outside vehicle. Then bring another electrical key transmitter sub-assembly for which operations are to be performed into vehicle.

4. Confirmation of ECU code
  • Perform operation according to prompts on the Techstream screen

5. Verification of unregistered electrical key transmitter sub-assembly*2
  1. While facing logo side of unregistered transmitter toward power switch, hold transmitter near power switch.
  2. Confirm that wireless door lock buzzer sounds twice (short beep)
  3. Bring electrical key transmitter sub-assembly for which operations have been completed outside vehicle. Then bring another electrical key transmitter sub-assembly for which operations are to be performed into vehicle.

6. Registration of ID code
  • Perform operation according to prompts on the Techstream screen

7. End of registration
  • Finish new key ID code registration
  • *1: Repeat this process for each electrical key transmitter sub-assembly registered to the vehicle. Finish the procedure for each electrical key transmitter sub-assembly within 30 seconds. If the procedure for any of the electrical key transmitter sub-assemblies is not finished within the specified time, perform the registration from process 1 again. When performing the electrical key transmitter sub-assembly confirmation procedure for an electrical key transmitter sub-assembly, the security indicator light comes on and remains on until all the electrical key transmitter sub-assemblies are confirmed.
  • *2: Repeat this process for each key which is to be registered to the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the electrical key transmitter sub-assemblies is not finished within the specified time, perform the registration from process 1 again.
  • If "Smart Access System with Push-button Start" is canceled, registration cannot be performed.

    Click here

7. KEY REGISTRATION (PROCEDURE "C")

(a) Additional key ID registration:

HINT:

In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate step numbers. Perform the steps in numerical order.

Process

Procedure

1. Start of registration
  1. Prepare all electrical key transmitter sub-assemblies to be registered and place them outside vehicle. Then bring 1 registered electrical key transmitter sub-assembly into vehicle.
  2. Connect the Techstream to DLC3
  3. While holding registered electrical key transmitter sub-assembly, turn power switch on (IG)
  4. Turn the Techstream on
  5. Enter following menus: Body Electrical / Smart Access / Utility / Smart Code Registration

2. Confirmation of registered electrical key transmitter sub-assembly*1
  1. Perform operation according to prompts on the Techstream screen
  2. While facing logo side of registered transmitter toward power switch, hold transmitter near power switch.
  3. Confirm that wireless door lock buzzer sounds once (short beep)

3. Confirmation of ECU code
  • Perform operation according to prompts on the Techstream screen

4. Verification of unregistered electrical key transmitter sub-assembly*2
  1. While facing logo side of unregistered transmitter toward power switch, hold transmitter near power switch.
  2. Confirm that wireless door lock buzzer sounds twice (short beep)

5. Registration of ID code
  • Perform operation according to prompts on the Techstream screen

6. End of registration
  • Finish key ID code registration
  • *1: Perform this process for one of the electrical key transmitter sub-assemblies registered to the vehicle. Finish the procedure within 30 seconds. If the procedure is not finished within the specified time, perform the registration from process 1 again.
  • *2: Repeat this process for each electrical key transmitter sub-assembly which is to be registered to the vehicle. Finish the procedure for each electrical key transmitter sub-assembly within 30 seconds. If the procedure for any of the electrical key transmitter sub-assemblies is not finished within the specified time, perform the registration from process 1 again.
  • If "Smart Access System with Push-button Start" is canceled, registration cannot be performed.

    Click here

8. KEY REGISTRATION (PROCEDURE "D")

(a) Key ID erasure:

NOTICE:

Do not erase all registered key codes except one electrical key transmitter sub-assembly (for card type) while the smart access system with push-button start cancel is activated. By doing so, the smart access system with push-button start cannot be returned to its original condition using the cancel operation. In addition, the entry unlock switching function cannot be used. However, erasing all registered key codes except one electrical key transmitter sub-assembly (for card type) will not cause problems if registering additional electrical key transmitter sub-assemblies (for standard type).

HINT:

  • This procedure clears all the registered key codes except one master electrical key transmitter sub-assembly code.
  • In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate step numbers. Perform the steps in numerical order.

Process

Procedure

1. Start of erasure
  1. Connect the Techstream to DLC3
  2. While holding registered electrical key transmitter sub-assembly, turn power switch on (IG)
  3. Turn the Techstream on
  4. Enter following menus: Body Electrical / Smart Access / Utility / Smart Code Erasure

2. Confirmation of registered electrical key transmitter sub-assembly*
  1. Perform operation according to prompts on the Techstream screen
  2. While facing logo side of registered transmitter toward power switch, hold transmitter near power switch.
  3. Confirm that wireless door lock buzzer sounds once (short beep)

    HINT:

    The security indicator light illuminates.

3. Confirmation of ECU code
  • Perform operation according to prompts on the Techstream screen

    HINT:

    The security indicator light goes off.

4. Erasure of ID code
  • Perform operation according to prompts on the Techstream screen

5. End of erasure
  • Finish key ID code erasure
  • *: Perform this process for one of the electrical key transmitter sub-assemblies registered to the vehicle. Finish the procedure within 30 seconds. If the procedure is not finished within the specified time, perform the erasure from process 1 again.
  • If "Smart Access System with Push-button Start" is canceled, erasure cannot be performed.

    Click here

9. KEY REGISTRATION (PROCEDURE "E")

(a) All keys ID erasure:

HINT:

In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate step numbers. Perform the steps in numerical order.

Process

Procedure

1. Start of erasure
  1. Connect the Techstream to DLC3
  2. While holding registered electrical key transmitter sub-assembly, turn power switch on (IG)
  3. Turn the Techstream on
  4. Enter following menus: Body Electrical / Smart Access / Utility / Smart Code Reset
  5. Read "Seed Number" sent from TIS according to the Techstream screen
  6. Input "Pass-Code Number" sent from TIS according to the Techstream screen

2. Confirmation of ECU code
  • Perform operation according to prompts on the Techstream screen

3. Erasure of ID code
  1. Perform operation according to prompts on the Techstream screen
  2. Wait for 15 minutes

4. End of erasure
  • Finish key ID code erasure
  • If "Smart Access System with Push-button Start" is canceled, erasure cannot be performed.

    Click here

10. KEY REGISTRATION (PROCEDURE "F")

(a) ECU code registration:

HINT:

In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate step numbers. Perform the steps in numerical order.

Process

Procedure

1. Start of registration
  1. Connect the Techstream to DLC3
  2. While holding registered electrical key transmitter sub-assembly, turn power switch on (IG)

    HINT:

    Power switch cannot be turned on (IG) more than 10 times. To continue electrical key transmitter sub-assembly registration procedure with power switch off, use either method below:

    • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
    • Connect the Techstream to DLC3 and select "Manual" from initial screen on the Techstream. Then select "Key Code Registration" under model code.
  3. Turn the Techstream on
  4. Enter following menus: Body Electrical / Smart Access / Utility / ECU Communication ID Registration / ID code box and Steering Lock

2. Confirmation of registered electrical key transmitter sub-assembly*
  1. While facing logo side of registered transmitter toward power switch, hold transmitter near power switch.
  2. Confirm that wireless door lock buzzer sounds once (short beep)

3. Erasure of ECU code
  • Perform operation according to prompts on the Techstream screen

4. End of registration
  • Finish ECU code registration
  • *: Perform this process for one of the electrical key transmitter sub-assemblies registered to the vehicle. Finish the procedure within 30 seconds. If the procedure is not finished within the specified time, perform the registration from process 1 again.
  • If "Smart Access System with Push-button Start" is canceled, registration cannot be performed.

    Click here

  • If there are any electronic devices near the driver seat which may cause wave interference, such as cell phones, personal computers, portable music players, other electrical key transmitter sub-assemblies, etc., turn them off or move them away from the driver seat.

11. KEY REGISTRATION (PROCEDURE "G")

(a) ECU communication ID registration:

NOTICE:

  • The ECU communication ID should be registered when the ID code box (immobiliser code ECU) is replaced in order for the ECU communication ID to match.
  • The ECU communication ID should be registered when the main body ECU (multiplex network body ECU) is replaced in order for the ECU communication ID to match.
  • The hybrid control system cannot be started unless the ECU communication ID is registered.
  • After registration, pressing the power switch may not start the hybrid control system on the first try. If so, press the power switch again.
  • After the hybrid control system is started, clear DTC B2799-790 (code for power management control ECU immobiliser communication error) using either of the following methods:

    - Use the Techstream.

    - Disconnect the cable from the negative (-) auxiliary battery terminal for 30 seconds.

Process

Procedure

1. Start of registration
  1. Connect the Techstream to the DLC3
  2. Turn the power switch on (IG)

    HINT:

    The security indicator light goes off.

  3. Turn the Techstream on
  4. Enter the following menus: Powertrain / Hybrid Control / Active Test / Connect the TC and TE1
  5. Turn the TC terminal ON to send a TC ON forced operation request

2. ECU communication ID registration
  1. After 30 minutes or more have elapsed, enter the following menus: Powertrain / Hybrid Control / Active Test / Connect the TC and TE1
  2. Turn the TC terminal OFF to send a TC ON forced operation cancellation request
  3. Turn the power switch off

    HINT:

    The security indicator light blinks.

3. Confirmation of registration
  1. Turn the power switch on (IG)

    HINT:

    The security indicator light goes off.

  2. Check that the hybrid control system starts and stays for more than 3 seconds

    NOTICE:

    • Do not open and close any doors. If any doors are opened and closed, start the registration over again from procedure 1 of this process.
    • There are cases in which the hybrid control system will not start on the first attempt after completing ECU communication ID code registration. However, this is not a malfunction, as the hybrid control system can be started normally from the second start attempt.

4. Clear DTC
  1. After confirming that the hybrid control system starts, use the Techstream to clear DTC B2799-790 "Engine Immobiliser System Malfunction"

5. End of registration
  • Finish ECU communication ID registration

12. REMOTE DOOR LOCK AND UNLOCK REGISTRATION (PROCEDURE "H")

Process

Procedure

1. Start of registration
  1. Connect the Techstream to DLC3
  2. Turn power switch on (IG)
  3. Turn the Techstream on
  4. Enter the following menus: Body Electrical / Telematics / Utility / Remote Door Lock Setting

2. Registration of remote door lock and unlock
  1. Perform operation according to prompts on the Techstream screen

3. End of registration
  • Finish remote door lock and unlock registration

13. REMOTE ENGINE START AND STOP REGISTRATION (PROCEDURE "I")

Process

Procedure

1. Start of registration
  1. Connect the Techstream to DLC3
  2. Turn power switch on (IG)
  3. Turn the Techstream on
  4. Enter following menus: Body Electrical / Smart Access / Utility / ECU Communication ID Registration / ID code box and Steering Lock

2. Registration of remote engine start and stop
  • Perform operation according to prompts on the Techstream screen

3. End of registration
  • Finish remote engine start and stop registration

READ NEXT:

 Problem Symptoms Table

PROBLEM SYMPTOMS TABLE HINT: Inspect the fuses and relays related to this system before inspecting the suspected areas below. If the problem only occurs in certain locations or at certain times o

 Terminals Of Ecu

TERMINALS OF ECU CHECK POWER SWITCH (a) Measure the voltage and resistance according to the value(s) in the table below. Terminal No. (Symbol) Input/Output Wiring Color Terminal Description

 Diagnosis System

DIAGNOSIS SYSTEM DESCRIPTION (a) The certification ECU (smart key ECU assembly) and hybrid vehicle control ECU control the vehicle immobiliser system functions. Immobiliser system data and Diagnostic

SEE MORE:

 Installation

INSTALLATION PROCEDURE 1. INSTALL TIRE PRESSURE WARNING ECU AND RECEIVER (a) Connect the connector to the tire pressure warning ECU and receiver. (b) Attach the 2 guides to temporarily install the tire pressure warning ECU and receiver. (c) Install the bolt. Torque: for bolt A : 8.3 N·m {85 kg

 Short in P/T Squib (RH) Circuit (B1900-B1903)

DESCRIPTION The front pretensioner RH circuit consists of the airbag ECU assembly and front seat outer belt assembly RH. This circuit instructs the SRS to deploy when deployment conditions are met. These DTCs are stored when a malfunction is detected in the front pretensioner RH circuit. DTC No.

© 2016-2024 Copyright www.lexunx.com