Lexus NX: Short in Sensor with Motor Power Supply Circuit (B2658)
DESCRIPTION
This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2658 | Short in Sensor with Motor Power Supply Circuit | Problem with the voltage supplied to the position control sensor. |
|
WIRING DIAGRAM
PROCEDURE
| 1. | CLEAR DTC |
(a) Clear the DTCs.
Click here .gif)
|
.gif)
| 2. | CHECK FOR DTC |
(a) Check for DTCs.
Click here
OK:
DTC B2658 is not output.
| OK | .gif) | USE SIMULATION METHOD TO CHECK |
|
| 3. | CHECK FRONT POWER SEAT SWITCH LH (SLIDE MOTOR CIRCUIT) |
| (a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
.png)
| NG | | GO TO STEP 6 |
|
| 4. | CLEAR DTC |
(a) Clear the DTCs.
Click here
|
| 5. | CHECK FOR DTC |
(a) Check for DTCs.
Click here
OK:
DTC B2658 is not output.
| OK | | USE SIMULATION METHOD TO CHECK |
| NG | | REPLACE FRONT POWER SEAT SWITCH LH |
| 6. | CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT SEAT ADJUSTER ASSEMBLY LH [SLIDE MOTOR]) |
(a) Disconnect the g12 front power seat switch LH connector.
(b) Disconnect the g10 front seat adjuster assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| g12-5 (SSRS) - g10-2 (O/P) | Always | Below 1 Ω |
| g12-5 (SSRS) or g10-2 (O/P) - Body ground | Always | 10 kΩ or higher |
| g12-1 (SGND) - g10-3 (GND) | Always | Below 1 Ω |
| g12-1 (SGND) or g10-3 (GND) - Body ground | Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 7. | REPLACE FRONT POWER SEAT SWITCH LH |
(a) Replace the front seat switch LH with new or known good one.
Click here
|
| 8. | CLEAR DTC |
(a) Clear the DTCs.
Click here
|
| 9. | CHECK FOR DTC |
(a) Check for DTCs.
Click here
OK:
DTC B2658 is not output.
| OK | | END (FRONT POWER SEAT SWITCH LH WAS DEFECTIVE) |
| NG | | REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH |
READ NEXT:
Front Power Seat does not Operate with Front Power Seat Switch
DESCRIPTION Signals are input into the front power seat switch LH. The built-in ECU manages the signals received from the power seat switch, and operates each motor. If the front power seat switch LH
One or more Power Seat Motors do not Operate
DESCRIPTION Signals are input into the front power seat switch LH. The built-in ECU manages the signals received from the front power seat switch LH, and operates each motor. If the front power seat s
Power Seat Position is not Memorized
DESCRIPTION The main body ECU (multiplex network body ECU) receives seat memory switch signals from the outer mirror control ECU assembly (for Driver Side) via CAN communication. If the seat memory SE
SEE MORE:
Diagnosis System
DIAGNOSIS SYSTEM DESCRIPTION (a) Sliding roof system data and Diagnostic Trouble Codes (DTCs) can be read through the vehicle Data Link Connector 3 (DLC3). When the system seems to be malfunctioning, use the Techstream to check for malfunctions and perform repairs. CHECK DLC3 (a) Check the DLC3. Cli
Installation
INSTALLATION PROCEDURE 1. INSTALL REAR HEADER SPEAKER ASSEMBLY NOTICE: Do not touch the cone part of the speaker. (a) Temporarily install the speaker by attaching the clip of the speaker to the vehicles body. (b) Install the rear header speaker assembly with the bolt. Torque: 7.5 N·
