Lexus NX: ASC ECU Communication Stop Mode

Lexus NX Service Manual / Power Source & Network / Networking / Can Communication System / ASC ECU Communication Stop Mode

DESCRIPTION

Detection Item	Symptom	Trouble Area
ASC ECU Communication Stop Mode	Any of the following conditions are met: Communication stop for "ASC" is indicated on the "Communication Bus Check" screen of the Techstream. Click here Communication system DTCs (DTCs that start with U) that correspond to "ASC ECU Communication Stop Mode" in "DTC Combination Table" are output. Click here	Stereo component equalizer assembly branch wire or connector Power source circuit of stereo component equalizer assembly Stereo component equalizer assembly ground circuit Stereo component equalizer assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here
When disconnecting and reconnecting the auxiliary battery.
Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here
Some parts must be initialized and set when replacing or removing and installing parts.
Click here
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here

HINT:

Operating the power switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.	CHECK FOR OPEN IN CAN BUS WIRE (STEREO COMPONENT EQUALIZER ASSEMBLY BRANCH WIRE)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

(b) Disconnect the stereo component equalizer assembly connector.

*a	Front view of wire harness connector (to Stereo Component Equalizer Assembly)

Standard Resistance:

Tester Connection	Condition	Specified Condition
I117-4 (CANH) - I117-12 (CANL)	Cable disconnected from negative (-) auxiliary battery terminal	54 to 69 Ω

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.	CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
I117-1 (GND) - Body ground	Cable disconnected from negative (-) auxiliary battery terminal	Below 1 Ω
I117-9 (GND1) - Body ground	Cable disconnected from negative (-) auxiliary battery terminal	Below 1 Ω

*a	Front view of wire harness connector (to Stereo Component Equalizer Assembly)

(b) Reconnect the cable to the negative (-) auxiliary battery terminal.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
I117-3(+B) - Body ground	Power switch off	11 to 14 V
I117-11(IG) - Body ground	Power switch on (IG)	11 to 14 V
I117-11(IG) - Body ground	Power switch off	Below 1 V

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

SEE MORE:

Fail-safe Chart

FAIL-SAFE CHART FAIL-SAFE FUNCTION (a) When communication fails in any of the CAN bus wires (communication wires), a fail-safe function(s) operates. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning. (b) Effects on each system when communi

Dtc Check / Clear

DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the intuitive parking assist system on. (d) Turn the Techstream on. (e) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Trouble Codes. (f) Check

Lexus NX: ASC ECU Communication Stop Mode

READ NEXT:

Vehicle Approaching Sound ECU Communication Stop Mode

Headup Display Communication Stop Mode

Millimeter Wave Radar Sensor Communication Stop Mode

SEE MORE:

Fail-safe Chart

Dtc Check / Clear