Lexus NX: Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)
DESCRIPTION
This DTC is stored when items controlled by the certification ECU cannot be customized via the audio and visual system vehicle customization screen.
HINT:
The certification ECU controls the smart access system with push-button start (for Entry Function) related items that are customizable via the multi-display assembly screen.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15F7 | Certification ECU Vehicle Information Reading/Writing Process Malfunction | Certification ECU vehicle setting processing error. |
|
CAUTION / NOTICE / HINT
NOTICE:
-
When replacing the radio receiver assembly, always replace it with a new one.
If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio receiver assembly may not operate normally.
-
Before replacing the certification ECU (smart key ECU assembly), refer to smart access system with push-button start (for Entry Function) Precaution.
Click here
.gif)
HINT:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here
PROCEDURE
| 1. | CHECK CAN COMMUNICATION SYSTEM |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here
OK:
CAN communication DTCs are not output.
| NG | .gif) | GO TO CAN COMMUNICATION SYSTEM |
|
.gif)
| 2. | CHECK SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function) |
(a) Check if the smart access system with push-button start (for Entry Function) is malfunctioning.
Click here
HINT:
Customization may not be possible depending on the malfunction in the smart access system with push-button start (for Entry Function).
OK:
No malfunctions are present in the smart access system with push-button start (for Entry Function).
| NG | | GO TO SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function) |
|
| 3. | CHECK CUSTOMIZE ITEMS |
(a) Display the "Vehicle Customization" screen.
(b) Make a note of the customizable items for each certification ECU related system.
HINT:
These items shown as customizable via the audio and visual system vehicle customization screen can also be changed manually. In a following step, a manual procedure will be used.
(1) Check the customize parameters list for the smart access system with push-button start (for Entry Function) related items that can be customized via the multi-display assembly screen.
Click here
(c) Manually change and confirm that it was possible to successfully change the settings of the customize parameters for each system that are available for customization via the multi-display assembly screen.
OK:
The items available for customization via the multi-display assembly screen can be customized successfully using the manual procedure.
| OK | | REPLACE RADIO RECEIVER ASSEMBLY |
| NG | | REPLACE CERTIFICATION ECU |
READ NEXT:
D-Seat ECU Vehicle Information Reading/Writing Process Malfunction (B15F8)
DESCRIPTION This DTC is stored when items controlled by the position control ECU assembly (driver seat) cannot be customized via the audio and visual system vehicle customization screen. HINT: The pos
XM Tuner Antenna Disconnected (B15FE,B15FF)
DESCRIPTION These DTCs are stored when a malfunction occurs in the roof antenna assembly which is connected to the radio receiver assembly. DTC No. Detection Item DTC Detection Condition Trou
Back Camera Disconnected (C1622)
DESCRIPTION This DTC is stored if the radio receiver assembly judges that the signals or signal lines between the television camera assembly and the multi-display assembly are not normal as a result o
SEE MORE:
Motor Drive Permission Malfunction (C1451)
DESCRIPTION If air bleeding has not been performed, the skid control ECU (brake booster with master cylinder assembly) stores DTC C1451 to prevent the entry of air due to pump motor operation. DTC C1451 is stored when Invalid Mode is selected, the system will not return to normal until the air bleed
Tires
Replace or rotate tires in accordance
with maintenance schedules
and treadwear.
Checking tires
Check if the treadwear indicators are
showing on the tires. Also check the
tires for uneven wear, such as excessive
wear on one side of the tread.
Check the spare tire condition and
pressure if
