Lexus NX: Dcm Operation History

DCM OPERATION HISTORY

HINT:

  • This function shows the telematics network status when the DCM (telematics transceiver) was operated. Use this when no DTC is present but this telematics system was unable to connect to the call center. This symptom may occur if cell phone signal strength is very weak.
  • This function is used to display operation history information and the time at which it was stored in the DCM (telematics transceiver).

DCM OPERATION HISTORY

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Choose "Telematics" from the System Selection Menu, and then click "Utility".

(e) Click "DCM Operation History" on the Utility Selection Menu.

Body Electrical > Telematics > Utility

Tester Display

DCM Operation History

(f) Choose "Items" on the DCM Operation History Menu.

HINT:

  • When "Operation Code" is recorded, DCM Operation History is displayed on the Techstream.
  • The displayed "Function" differs depending on the selected "Items".

(g) Refer to the following chart and check the system operation status displayed on the Techstream. (The following chart is an example of the system operation status.)

System Operation Status Example

Occurrence Time*1

Operation Code*2

Function*3

Content*4

Roaming*5

Voice Call*6

Service Area*7

Electric Level*8

2017/12/31 12:40:50

0101

GNSS (Satellite)

Unreceived GNSS (Satellite) signal

ON

With

Out of Service

Level 0

Tester Display Description

Tester Display

Description

Range

*1

Occurrence time

Indicates date of the DCM (telematics transceiver) operation.

-

*2

Operation Code

Indicates the Operation Code.

-

*3

Function

Items

Indicates the function name.

-

Common

  • GNSS (Satellite)
  • Collision Detection
  • Network Power Supply Control
  • SMS
  • Telematics PF
  • Failure Due to Conflict
  • Activate Function

Emergency Call

  • Emergency Call
  • Automatic Maintenance
  • Manual Maintenance

*4

Content

Indicates the content.

-

*5

Roaming

Indicates whether roaming was used for the communication network.

ON or OFF

*6

Voice Call

Indicates whether there was a voice call.

With or Without

*7

Service Area

Indicates whether the vehicle was in the service area.

Out of Service, Within Range, OFF the Air or Start up (LTE)

*8

Electric Level

Indicates the strength of the cellular signal received by the vehicle.

Level 0, Level 1, Level2, Level3, Level 4, Level 5

READ NEXT:

 Dcm Activation

DCM ACTIVATION DCM ACTIVATION (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Choose "Telematics" from the System Selection Menu, and then cl

 Acn Call End

ACN CALL END ACN CALL END This function terminates the ACN (Automatic Collision Notification) to the telematics provider. After a collision in which the DCM receives "Collision Detection Signal", the

 Customize Parameters

CUSTOMIZE PARAMETERS CUSTOMIZE TELEMATICS SYSTEM (a) Customizing with the Techstream. NOTICE: When the customer requests a change in a function, first make sure that the function can be customized.

SEE MORE:

 Repair

REPAIR CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. If the installation area of the headlight assembly is damaged, use the supply retainer for low-cost repair. Make sure that the headlight assembly is not damage

 Different Diameter Tire Malfunction (C1348)

DESCRIPTION If the hybrid vehicle control ECU receives a signal from the skid control ECU (brake booster with master cylinder assembly) that the AWD system is malfunctioning, the hybrid vehicle control ECU outputs this DTC. DTC No. Detection Item INF Code DTC Detection Condition Trouble A

© 2016-2025 Copyright www.lexunx.com