Lexus NX: Installation
INSTALLATION
PROCEDURE
1. INSTALL BATTERY COOLING BLOWER ASSEMBLY LH
CAUTION:
Wear insulated gloves and use insulated tools.
(a) Install the battery cooling blower assembly LH with the 3 nuts.
Torque:
7.5 N·m {76 kgf·cm, 66 in·lbf}
(b) Connect the wire harness clamp and connector.
2. INSTALL BATTERY COOLING BLOWER ASSEMBLY RH
CAUTION:
Wear insulated gloves and use insulated tools.
(a) Install the battery cooling blower assembly RH with the 3 nuts.
Torque:
7.5 N·m {76 kgf·cm, 66 in·lbf}
(b) Connect the wire harness clamp and connector.
3. INSTALL NO. 4 HYBRID BATTERY EXHAUST DUCT
(a) Install the No. 4 hybrid battery exhaust duct to the No. 2 hybrid battery exhaust duct.
4. INSTALL NO. 3 HYBRID BATTERY EXHAUST DUCT
(a) Install the No. 3 hybrid battery exhaust duct to the No. 1 hybrid battery exhaust duct.
5. CONNECT NO. 2 HYBRID BATTERY INTAKE DUCT
CAUTION:
Wear insulated gloves.
(a) Connect the No. 2 hybrid battery intake duct with the 2 clips.
6. CONNECT NO. 1 HYBRID BATTERY INTAKE DUCT
CAUTION:
Wear insulated gloves.
(a) Connect the No. 1 hybrid battery intake duct with the 2 clips.
7. INSTALL NO. 2 TOOL BOX SUB-ASSEMBLY
Click here .gif)
8. INSTALL NO. 1 TOOL BOX SUB-ASSEMBLY
Click here
9. INSTALL DECK FLOOR BOX RH
Click here
10. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY
Click here
11. INSTALL REAR DECK FLOOR BOX
Click here
12. INSTALL SEATBACK ASSEMBLY RH
for Manual Seat: Click here
for Power Seat: Click here
13. CONNECT INVERTER RESERVE TANK ASSEMBLY
Click here
14. CONNECT WIRE HARNESS
Click here
15. INSTALL SERVICE PLUG GRIP
Click here
16. INSTALL HYBRID BATTERY SERVICE PLUG COVER
Click here
17. INSTALL BATTERY SERVICE HOLE COVER
Click here
18. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
19. INITIALIZATION AFTER RECONECTING AUXILIARY BATTERY TERMINAL
Click here
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
20. INSTALL DECK FLOOR BOX LH
Click here
21. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
Click here
22. INSTALL DECK BOARD ASSEMBLY
Click here
23. INSTALL TONNEAU COVER ASSEMBLY
Click here
READ NEXT:
Components
COMPONENTS ILLUSTRATION *A for Manual Seat *B for Power Seat *1 NO. 2 BATTERY SERVICE COVER BOARD *2 NO. 3 BATTERY SERVICE COVER BOARD *3 REAR DOOR SCUFF PLATE LH *4 REAR
Removal
REMOVAL PROCEDURE 1. REMOVE REAR SEAT CUSHION ASSEMBLY for Manual seat: Click here for Power seat: Click here 2. REMOVE REAR DOOR SCUFF PLATE LH Click here 3. REMOVE REAR DOOR SCUFF PLATE RH
SEE MORE:
Relay
On-vehicle InspectionON-VEHICLE INSPECTION PROCEDURE 1. INSPECT PTC HEATER RELAY(PTC HTR NO. 1, NO. 3) (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 3 - 5 Auxiliary battery voltage is no
Transmitter Battery
ReplacementREPLACEMENT PROCEDURE 1. REMOVE TRANSMITTER BATTERY (a) Push the release hook knob and extract the mechanical key. (b) Using a screwdriver with its tip wrapped in protective tape, remove the transmitter housing cover as shown in the illustration. HINT: Tape the screwdri
