Lexus NX: Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL REAR DOOR REAR WINDOW FRAME MOULDING LH
(a) Install a new rear door rear window frame moulding LH.
(b) Install a nose piece to an air riveter or hand riveter.
(c) Insert the mandrel part of a new rivet into the nose piece.
(d) Place the riveter upright against the rear door rear window frame moulding LH and install the 3 rivets.
NOTICE:
-
Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.
.png)
*1
Riveter
*2
Mandrel
*a
INCORRECT
*b
CORRECT
-
Confirm that the rivets are seated properly against the rear door rear window frame moulding LH.
.png)
*1
Riveter
*a
INCORRECT
*b
CORRECT
- Do not tilt the riveter when installing the rivet to the rear door rear window frame moulding LH.
- Do not leave any space between the rivet head and rear door rear window frame moulding LH.
-
Do not leave any space between the rear door rear window frame moulding LH and rear door panel. Firmly hold together the 2 items while installing the rivet.
.png)
*1
Riveter
*a
INCORRECT
*b
CORRECT
HINT:
If the rivet cannot be cut, pull it once and cut it.
2. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING LH
(a) Install the rear door upper window frame moulding LH.
(b) Install a nose piece to an air riveter or hand riveter.
(c) Insert the mandrel part of a new rivet into the nose piece.
(d) Place the riveter upright against the rear door rear window frame moulding LH and install the 4 rivets.
NOTICE:
-
Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.
*1
Riveter
*2
Mandrel
*a
INCORRECT
*b
CORRECT
-
Confirm that the rivets are seated properly against the rear door upper window frame moulding LH.
*1
Riveter
*a
INCORRECT
*b
CORRECT
- Do not tilt the riveter when installing the rivet to the rear door upper window frame moulding LH.
- Do not leave any space between the rivet head and rear door upper window frame moulding LH.
-
Do not leave any space between the rear door upper window frame moulding LH and rear door panel. Firmly hold together the 2 items while installing the rivet.
*1
Riveter
*a
INCORRECT
*b
CORRECT
HINT:
If the rivet cannot be cut, pull it once and cut it.
3. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH
HINT:
When installing the rear door front window frame moulding LH, heat the rear door panel and rear door front window frame moulding LH using a heat light.
Standard:
| Item | Temperature |
|---|---|
| Rear Door Panel | 40 to 60°C (104 to 140°F) |
| Rear Door Front Window Frame Moulding LH | 20 to 30°C (68 to 86°F) |
NOTICE:
Do not heat the rear door panel and rear door front window frame moulding LH excessively.
(a) Clean the rear door panel surface.
(1) Using a heat light, heat the rear door panel surface.
(2) Remove the double-sided tape from the rear door panel surface.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Install a new rear door front window frame moulding LH.
(1) Using a heat light, heat the rear door front window frame moulding LH and the rear door panel surface.
(2) Remove the peeling paper from the face of the rear door front window frame moulding LH.
HINT:
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
| (3) Attach the clip and guide to install the rear door front window frame moulding LH. HINT: Press the rear door front window frame moulding LH firmly to install it. |
|
4. INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH
Click here .gif)
5. INSTALL REAR DOOR FRAME GARNISH LH
Click here
6. INSTALL REAR DOOR WEATHERSTRIP LH
Click here
7. CONNECT REAR DOOR CHECK ASSEMBLY LH
Click here
8. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
Click here
9. INSTALL REAR DOOR REAR GUIDE SEAL LH
Click here
10. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH
Click here
11. INSTALL REAR DOOR GLASS RUN LH
Click here
12. INSTALL REAR DOOR SERVICE HOLE COVER LH
Click here
13. INSTALL REAR DOOR ARMREST SET BRACKET LH
Click here
14. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH
Click here
15. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Click here
16. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Click here
17. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH
Click here
18. INSTALL REAR DOOR TRIM COVER LH
Click here
19. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
20. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click here
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
21. INSTALL DECK FLOOR BOX LH
Click here
22. INSTALL REAR DECK FLOOR BOX
Click here
23. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
Click here
24. INITIALIZE POWER WINDOW CONTROL SYSTEM
Click here
25. CHECK POWER WINDOW CONTROL SYSTEM
Click here
READ NEXT:
Components
COMPONENTS ILLUSTRATION *1 BACK DOOR CENTER GARNISH *2 REAR SIDE SPOILER SUB-ASSEMBLY LH *3 REAR SIDE SPOILER SUB-ASSEMBLY RH *4 REAR SPOILER ASSEMBLY *5 HOLE PLUG - -
Removal
REMOVAL PROCEDURE 1. REMOVE BACK DOOR CENTER GARNISH Click here 2. REMOVE REAR SPOILER ASSEMBLY (a) Remove the 2 hole plugs. Nut Bolt Connector (b) Remove the 4 nuts. (c) Re
SEE MORE:
Removal
REMOVAL PROCEDURE 1. PRECAUTION NOTICE: After turning the power switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal. Click here 2. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (a) Disable the auto tilt away function
Parts Location
PARTS LOCATION ILLUSTRATION *1 NO. 1 ENGINE ROOM RELAY BLOCK
EPB NO. 1 FUSE
EPB NO. 2 FUSE
HINT: EPB stands for Electric Parking Brake. *2 NO. 2 ENGINE ROOM RELAY BLOCK
ECU-B NO. 1 FUSE
ECU-B NO. 2 FUSE
*3 SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
