Lexus NX manuals

Lexus NX: Installation

Lexus NX Service Manual / Vehicle Interior / Seat / Front Seat Cushion Heater / Installation

INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:

  • Use the same procedure for the RH and LH sides.
  • The procedure listed below is for the LH side.

PROCEDURE

1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER LH

HINT:

  • When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

    Click here

  • Align the seam allowance in a single direction as shown in the illustration.

(a) Using hog ring pliers, install the separate type front seat cushion cover LH to the separate type front seat cushion pad LH with 4 new hog rings in the order indicated in the illustration.

NOTICE:

  • Be careful not to damage the separate type front seat cushion cover.
  • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

*1

Hog Ring Pliers

(b) Return the seat cover wire to its original position.

HINT:

Use the same procedure for both seat cover wires.

(c) Using hog ring pliers, install the separate type front seat cushion cover LH to the separate type front seat cushion pad LH with 14 new hog rings in the order indicated in the illustration.

NOTICE:

  • Be careful not to damage the separate type front seat cushion cover.
  • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

*1

Hog Ring Pliers

(d) Using hog ring pliers, install 2 new hog rings.

NOTICE:

  • Be careful not to damage the separate type front seat cushion cover.
  • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

*1

Hog Ring Pliers

2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD LH

Click here

3. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

Click here

4. INSTALL FRONT SEAT CUSHION SHIELD LH

Click here

5. INSTALL FRONT LOWER SEAT CUSHION SHIELD

Click here

6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

Click here

7. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

Click here

8. INSTALL FRONT SEAT ASSEMBLY LH

Click here

READ NEXT:

 Front Seatback Heater

 Components

COMPONENTS ILLUSTRATION *1 FRONT INNER SEAT CUSHION SHIELD LH *2 FRONT LOWER SEAT CUSHION SHIELD *3 FRONT SEAT CUSHION SHIELD LH *4 FRONT SEAT HEADREST SUPPORT *5 SEPARATE TY

 Removal

REMOVAL CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. HINT: Use the same procedure for the RH and LH sides. The procedure listed below i

SEE MORE:

 Airbag ECU Malfunction (B1000)

DESCRIPTION The airbag ECU assembly consists of a deceleration sensor, safing sensor, drive circuit, diagnosis circuit, ignition control, etc. If the airbag ECU assembly receives signals from the deceleration sensor, it determines whether or not the SRS should be activated. DTC B1000 is stored when

 Removal

REMOVAL PROCEDURE 1. PRECAUTION CAUTION: Be sure to read Precoution thoroughly before serving. Click here NOTICE: After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal. Click here 2. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

© 2016-2025 Copyright www.lexunx.com