Lexus NX manuals

Lexus NX: Open in Rear Floor Electrical Key Oscillator Circuit (B27A6)

Lexus NX Service Manual / Vehicle Interior / Theft Deterrent / Keyless Entry / Smart Access System With Push-button Start (for Entry Function) / Open in Rear Floor Electrical Key Oscillator Circuit (B27A6)

DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 2 indoor electrical key antenna assembly (rear floor). For the No. 2 indoor electrical key antenna assembly (rear floor) to detect when the electrical key transmitter sub-assembly is in the cabin, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A6 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor) (between terminals CLG6 and ANTE6, or terminals CG6B and CLGB).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B27A6

Open in Rear Floor Electrical Key Oscillator Circuit

An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor) (CLG6 - ANTE6, CG6B - CLGB) (1 trip detection logic*).
  • Certification ECU (smart key ECU assembly)
  • No. 2 indoor electrical key antenna assembly (rear floor)
  • Harness or connector
  • Any time
  • *: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Operation when Malfunction Detected

When electrical key transmitter sub-assembly is in rear seat area:

  • Power source mode does not change when power switch pressed
  • Electrical key transmitter sub-assembly locked inside vehicle

-
Related Data List and Active Test

DTC No.

Data List and Active Test

B27A6

Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • The smart access system with push-button start (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart access system with push-button start (for Entry Function) after confirming that the communication systems are functioning properly.

    Click here

  • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • Before replacing the certification ECU (smart key ECU assembly), refer to smart access system with push-button start (for Entry Function) Precaution.

    Click here

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE

1.

CHECK CONNECTOR CONNECTION

(a) Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor).

OK:

Connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY
OK

2.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

(a) Disconnect the I52 and I53 certification ECU (smart key ECU assembly) connectors.

(b) Disconnect the I25 No. 2 indoor electrical key antenna assembly (rear floor) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I52-15 (CLG6) - I25-1 (ANTE6)

Always

Below 1 Ω

I52-14 (CG6B) - I25-3 (CLGB)

Always

Below 1 Ω

I53-11 (E) - Body ground

Always

Below 1 Ω

I52-15 (CLG6) or I25-1 (ANTE6) - Body ground

Always

10 kΩ or higher

I52-14 (CG6B) or I25-3 (CLGB) - Body ground

Always

10 kΩ or higher

(d) Reconnect the I52 and I53 certification ECU (smart key ECU assembly) connectors.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

*a

Component with harness connected

(Certification ECU (Smart Key ECU Assembly))

*b

Waveform 1

*c

For 30 seconds after closing any door using the door outside handle

*d

30 seconds or more have elapsed after closing any door using the door outside handle

(a) Using an oscilloscope, check the waveform.

OK:

Tester Connection

Condition

Tool Setting

Specified Condition

I52-15 (CLG6) - I53-11 (E)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. Within 30 seconds of closing any door using the door outside handle

2 V/DIV., 500 ms/DIV.

Pulse generation

(See waveform 1)

I52-14 (CG6B) - I53-11 (E)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. Within 30 seconds of closing any door using the door outside handle

2 V/DIV., 500 ms/DIV.

Pulse generation

(See waveform 1)
NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

OK

4.

REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

(a) Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new one.

Click here

NEXT

5.

CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Smart Access > Clear DTCs
NEXT

6.

CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Smart Access > Trouble Codes

OK:

DTC B27A6 is not output.

OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR) WAS DEFECTIVE)
NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

READ NEXT:

 Open in Inside Luggage Compartment Electrical Key Oscillator Circuit (B27A7)

DESCRIPTION The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key antenna assembly (inside luggage). For the No. 3 indoo

 Open in Outside Luggage Compartment Electrical Key Antenna Circuit (B27A8)

DESCRIPTION The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage compartment). For the electrical key anten

 All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate

DESCRIPTION If the entry lock and wireless lock operations cannot be performed, there may be door control receiver malfunctions, wave interference or problems in the communication which is used for th

SEE MORE:

 Telephone Sub Antenna Circuit Short to Ground (B153711,B153713)

DESCRIPTION These DTCs are stored when a malfunction occurs in the telephone antenna (navigation antenna assembly) DTC No. Detection Item DTC Detection Condition Trouble Area B153711 Telephone Sub Antenna Circuit Short to Ground Telephone antenna (sub) impedance (Ω) is lower than t

 System Description

SYSTEM DESCRIPTION GENERAL The windshield deicer thin heater wires are attached to the inside of the windshield glass to help deice the window surface more quickly. The indicator light illuminates while the system is operating. The system automatically turns off after approximately 15 minutes. NOTIC

© 2016-2024 Copyright www.lexunx.com