Lexus NX: Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After the power switch off is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click here .gif)
2. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY
Click here
3. REMOVE REAR DECK FLOOR BOX
Click here
4. REMOVE DECK FLOOR BOX LH
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here
6. REMOVE FRONT DOOR TRIM COVER LH
Click here
7. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH
Click here
8. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL
Click here
9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Click here
10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH
Click here
11. REMOVE FRONT DOOR ARMREST SET BRACKET LH
Click here
12. REMOVE FRONT DOOR SERVICE HOLE COVER LH
Click here
13. REMOVE FRONT DOOR GLASS RUN LH
Click here
14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Click here
15. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH
Click here
16. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY
Click here
17. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH
Click here
18. DISCONNECT FRONT DOOR CHECK ASSEMBLY LH
| (a) Remove the bolt and disconnect the front door check assembly LH. |
|
19. REMOVE FRONT DOOR WEATHERSTRIP LH
Click here
20. REMOVE UPPER DOOR FRAME GARNISH LH
Click here
21. REMOVE FRONT DOOR FIX WINDOW GLASS LH
Click here
22. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH
Click here
23. REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH
Click here
24. REMOVE NO. 3 BLACK OUT TAPE LH
HINT:
When removing the No. 3 black out tape LH, heat the front door panel and No. 3 black out tape LH using a heat light.
Standard:
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| No. 3 Black Out Tape LH | 20 to 30°C (68 to 86°F) |
NOTICE:
Do not heat the front door panel or No. 3 black out tape LH excessively.
| (a) Pull back an edge of the No. 3 black out tape LH and pull it parallel to the front door panel to remove it. |
|
25. REMOVE NO. 2 BLACK OUT TAPE LH
HINT:
When removing the No. 2 black out tape LH, heat the front door panel and No. 2 black out tape LH using a heat light.
Standard:
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| No. 2 Black Out Tape LH | 20 to 30°C (68 to 86°F) |
NOTICE:
Do not heat the front door panel or No. 2 black out tape LH excessively.
| (a) Pull back an edge of the No. 2 black out tape LH and pull it parallel to the front door panel to remove it. |
|
26. REMOVE NO. 1 BLACK OUT TAPE LH
HINT:
When removing the No. 1 black out tape LH, heat the front door panel and No. 1 black out tape LH using a heat light.
Standard:
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| No. 1 Black Out Tape LH | 20 to 30°C (68 to 86°F) |
NOTICE:
Do not heat the front door panel or No. 1 black out tape LH excessively.
| (a) Pull back an edge of the No. 1 black out tape LH and pull it parallel to the front door panel to remove it. |
|
READ NEXT:
Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PROCEDURE 1. REPAIR INSTRUCTION (a) Clean the vehicle
Components
COMPONENTS ILLUSTRATION *1 DECK FLOOR BOX LH *2 NO. 3 DECK BOARD SUB-ASSEMBLY *3 REAR DECK FLOOR BOX *4 NEGATIVE AUXILIARY BATTERY TERMINAL N*m (kgf*cm, ft.*lbf): Specified
SEE MORE:
Oxygen Sensor Circuit (Bank 1 Sensor 2) (P0136-P0139,P013A)
DESCRIPTION In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that
Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be dis
