Lexus NX: Touch Pad Memory Module Malfunction (B155B)

DESCRIPTION

This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad memory module malfunction.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B155B

Touch Pad Memory Module Malfunction

Internal memory module malfunction

Remote operation controller assembly (remote touch)

PROCEDURE

1.

CHECK DTC

(a) Clear the DTCs.

Click here

Body Electrical > Navigation System > Clear DTCs

(b) Recheck for DTCs and check that no DTCs are output.

Click here

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

USE SIMULATION METHOD TO CHECK

NG

2.

CHECK INFORMATION CODE

(a) Check that the part number of the remote operation controller assembly (remote touch) is correct.

Result

Proceed to

The part number of the remote operation controller assembly (remote touch) is correct

A

The part number of the remote operation controller assembly (remote touch) is incorrect

B

B

REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH)

A

3.

REMOTE TOUCH SELF CHECK (CHECK TOUCH SCREEN OPERATION POSITION RECOGNITION CONDITION)

(a) Enter self-diagnostic mode.

Click here

(b) Operate the remote touch screen laterally and check that the touch screen generates vibration feedback.

NOTICE:

Since the remote touch screen may recognize a pinch in/out or flick operation if operated with 2 fingers, always use 1 finger to operate the remote touch in self-diagnostic mode.

HINT:

When operating at an excessively low temperature, vibration feedback may be difficult to feel.

Result

Proceed to

Vibration feedback is generated according to touch panel operation

A

The switch illumination changes but vibration feedback is not generated in accordance to touch screen operation

B

B

REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH)

A

4.

CHECK DTC

(a) Clear the DTCs.

Click here

Body Electrical > Navigation System > Clear DTCs

(b) Turn the power switch off.

(c) Turn the power switch on (ACC) and wait for 5 seconds.

(d) Recheck for DTCs and check that no DTCs are output.

Click here

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

USE SIMULATION METHOD TO CHECK

NG

REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH)

READ NEXT:

 GVIF Disconnected (from EMV/MM Integrated Device to Multi Display) (B1575)

DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area B1575 GVIF Disconnected (from EMV/MM Integrated Device to Multi Display) GVIF disconnected (from radio receiver

 Voice Recognition Microphone Disconnected (B1579)

DESCRIPTION The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines. This DTC is stored when a microphone conne

 USB Device Malfunction (B1585)

DESCRIPTION This DTC is stored when a malfunction occurs in a connected device. DTC No. Detection Item DTC Detection Condition Trouble Area B1585 USB Device Malfunction When one of th

SEE MORE:

 Oil Pressure Switch

ComponentsCOMPONENTS ILLUSTRATION *1 ENGINE OIL PRESSURE SWITCH ASSEMBLY - - N*m (kgf*cm, ft.*lbf): Specified torque TOYOTA Genuine Adhesive 1344, Three Bond 1344 or equivalent. ★ Precoated part - - RemovalREMOVAL PROCEDURE 1. REMOVE ENGINE OIL PRESSURE SWITCH

 Open in IG Circuit (B242E)

DESCRIPTION This DTC is output when there is a problem in the power supply for the headlight ECU sub-assembly RH. The headlight ECU sub-assembly LH outputs DTC B242E. DTC No. Detection Item DTC Detection Condition Trouble Area B242E Open in IG Circuit IG circuit malfunction in the h

© 2016-2025 Copyright www.lexunx.com