Lexus NX: Touch Pad Vibration Driver Malfunction (B155A)
DESCRIPTION
This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad vibration driver malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B155A | Touch Pad Vibration Driver Malfunction | Internal vibration driver malfunction | Remote operation controller assembly (remote touch) |
PROCEDURE
| 1. | CHECK DTC |
(a) Clear the DTCs.
Click here .gif)
(b) Recheck for DTCs and check that no DTCs are output.
Click here
OK:
No DTCs are output.
HINT:
If DTC B155B, B1559 is output, perform troubleshooting for DTC B155B, B1559 first.
B155B: Click here
B1559: Click here
| OK | .gif) | USE SIMULATION METHOD TO CHECK |
|
.gif)
| 2. | REMOTE TOUCH SELF CHECK (CHECK TOUCH SCREEN OPERATION POSITION RECOGNITION CONDITION) |
(a) Enter self-diagnostic mode.
Click here
(b) Operate the remote touch screen laterally and check that the touch screen generates vibration feedback.
NOTICE:
Since the remote touch screen may recognize a pinch in/out or flick operation if operated with 2 fingers, always use 1 finger to operate the remote touch in self-diagnostic mode.
HINT:
When operating at an excessively low temperature, vibration feedback may be difficult to feel.
| Result | Proceed to |
|---|---|
| Vibration feedback is generated according to touch panel operation | A |
| The switch illumination changes but vibration feedback is not generated in accordance to touch screen operation | B |
| B | | REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH) |
|
| 3. | CLEAR DTC |
(a) Clear the DTCs.
Click here
|
| 4. | CHECK FEEDBACK VIBRATION |
(a) Turn the power switch on (ACC), swipe the MENU screen to move the cursor and pull it over the button with the vibration feedback.
HINT:
Using the multi-display assembly customize setting screen, check that the remote touch screen vibration feedback reaction force setting is not set to "NO VIBRATION".
Click here
|
| 5. | CHECK DTC |
(a) Recheck for DTCs and check if the same DTC is output again.
Click here
OK:
No DTCs are output.
| OK | | USE SIMULATION METHOD TO CHECK |
| NG | | REPLACE REMOTE OPERATION CONTROLLER ASSEMBLY (REMOTE TOUCH) |
READ NEXT:
Touch Pad Memory Module Malfunction (B155B)
DESCRIPTION This DTC is stored if the remote operation controller assembly (remote touch) detects a malfunction in itself, such as internal hardware failure or touch pad memory module malfunction.
GVIF Disconnected (from EMV/MM Integrated Device to Multi Display) (B1575)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area B1575 GVIF Disconnected (from EMV/MM Integrated Device to Multi Display) GVIF disconnected (from radio receiver
Voice Recognition Microphone Disconnected (B1579)
DESCRIPTION The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines. This DTC is stored when a microphone conne
SEE MORE:
Parts Location
PARTS LOCATION ILLUSTRATION *A w/ Rear Seat Heater - - *1 AIR CONDITIONING CONTROL ASSEMBLY *2 SEAT HEATER SWITCH (for Driver Side) *3 SEAT HEATER SWITCH (for Front Passenger Side) *4 NO. 3 RELAY BLOCK
- RR S-HTR RELAY (w/ Rear Seat Heater)
*5 REFRESHING SEA
Cargo and luggage
Take notice of the following information
about storage precautions,
cargo capacity and load.
WARNING
■Things that must not be carried in the
luggage compartment
The following things may cause a fire if
loaded in the luggage compartment:
Receptacles containing gasoline
Aerosol cans
