Lexus NX: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Turn the power switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / Occupant Detection / Data List.
(f) Check the values by referring to the table below.
Body Electrical > Occupant Detection > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IG Switch | Power switch condition | ON/OFF | ON: Power switch on (IG) OFF: Power switch off | "OFF" is also displayed for this item when the power switch is on (ACC). |
| Passenger Buckle SW | Front seat belt assembly RH buckle switch | Set, Unset or NG | Set: The front seat belt assembly RH is fastened Unset: The front seat belt assembly RH is not fastened NG: Data is not determined | - |
| Passenger Classification | Front passenger classification | AM50/AF05/Child/CRS/OFF | AM50: Adult is seated AF05: Adult is seated Child: Child is seated CRS: Child restraint system is installed OFF: Vacant | - |
| Sensor Range Info | Sensor range information | OK/NG | OK: The value of an occupant detection sensor is within the range NG: The value of an occupant detection sensor is over the range | As sensor range is not set, OK is always displayed |
| FL Sensor Range Info | Front left sensor range information | OK | OK | As front left sensor range is not set, OK is always displayed |
| RL Sensor Range Info | Rear left sensor range information | OK | OK | As rear left sensor range is not set, OK is always displayed |
| FL Sensor Voltage | Front left sensor voltage | Min.: 0 V Max.: 19.8 V | 0 to 5 V | - |
| RL Sensor Voltage | Rear left sensor voltage | Min.: 0 V Max.: 19.8 V | 0 to 5 V | - |
| FL Sensor Weight Info | Front left sensor weight information | Min.: -10 kg (-22.0 lb) Max.: 20 kg (44.1 lb) | -10 to 20 kg (-22.0 to 44.1 lb) | - |
| RL Sensor Weight Info | Rear left sensor weight information | Min.: -10 kg (-22.0 lb) Max.: 30 kg (66.1 lb) | -10 to 30 kg (-22.0 to 66.1 lb) | - |
| Total Weight Information | Total weight information | Min.: -40 kg (-88.2 lb) Max.: 100 kg (220.5 lb) | -40 to 100 kg (-88.2 to 220.5 lb) | - |
| Number of Present DTC | Number of present DTCs recorded | Min.: 0, Max.: 255 | 0 | - |
| Number of Past DTC | Number of past DTC recorded | Min.: 0, Max.: 255 | 0 | - |
READ NEXT:
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Occupant Classification System DTC No. Detection Item Link B1771 Passenger Side Buckle Switch Circuit Malfunction B1780 Front Occupant Classificat
Passenger Side Buckle Switch Circuit Malfunction (B1771)
DESCRIPTION The front passenger side buckle switch circuit consists of the occupant detection ECU and front seat inner belt assembly RH. DTC B1771 is stored when a malfunction is detected in the front
Front Occupant Classification Sensor LH Circuit Malfunction (B1780)
DESCRIPTION The front occupant classification sensor LH circuit consists of the occupant detection ECU and front occupant classification sensor LH. DTC B1780 is stored when a malfunction is detected i
SEE MORE:
A/C Inverter High Voltage Output System Malfunction (B1472)
DESCRIPTION The inverter in the compressor with motor assembly outputs high-voltage to operate the motor. If there is an open or short in the output circuit, the hybrid vehicle control ECU will stop compressor operation and store this DTC. This DTC will be stored as a history DTC. The compressor ope
Sliding Roof Switch Assembly
ComponentsCOMPONENTS ILLUSTRATION *1 MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY) - - InspectionINSPECTION PROCEDURE 1. INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY) (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: T
