Lexus NX: Entry Unlock and Unlatch Functions do not Operate Using Kick Sensor
DESCRIPTION
If the hands free power back door operation does not operate, it could indicate the certification ECU (smart key ECU assembly) did not transmit a power back door open request signal, or a malfunction in the power back door system.
CAUTION / NOTICE / HINT
NOTICE:
-
The smart access system with push-button start (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart access system with push-button start (for Entry Function) after confirming that the communication systems are functioning properly.
Click here
.gif)
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
-
Before replacing the certification ECU (smart key ECU assembly), refer to smart access system with push-button start (for Entry Function) Precaution.
Click here
- After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
PROCEDURE
| 1. | CHECK CUSTOMIZE SETTING (KICK SENSOR FUNCTION) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Customize Setting / PSD & PBD operation.
PSD & PBD operation| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Kick Sensor Function | Function that enables/disables the touchless power back door. | ON | 0:OFF,1:ON | Multiplex network door ECU |
| Kick Sensor Operation with ACC ON | Status of the touchless power back door function with power switch on (ACC). | Available | 0:Available,1:Not Available | Main body ECU (multiplex network body ECU) |
| Result | Proceed to |
|---|---|
| The customize setting is "ON" and "Available" | A |
| The customize setting is "OFF" or "Available" | B |
| B | .gif) | PERFORM CUSTOMIZE SETTING |
|
.gif)
| 2. | CHECK OPERATION HISTORY |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Access / Utility / Operation History.
Body Electrical > Smart Access > Utility| Tester Display |
|---|
| Operation History |
| Parameter Name | Content |
|---|---|
| Kick Sensor Open Request Signal. | The multiplex network door ECU receives kick detection signals from the kick door control sensor and sends certification requests to the certification ECU (smart key ECU assembly). If certification is OK, an open permission is sent to the multiplex network door ECU. |
| Result | Proceed to |
|---|---|
| Not output | A |
| "Kick Sensor Open Request Signal" is output | B |
| B | | GO TO POWER BACK DOOR SYSTEM |
|
| 3. | CHECK ENTRY BACK DOOR OPEN FUNCTION |
(a) While carrying the electrical key transmitter sub-assembly, check that the entry unlock function operates when the back door opener switch is operated.
Click here
| Result | Proceed to |
|---|---|
| Entry back door open function operates | A |
| Entry back door open function does not operate | B |
| A | | GO TO POWER BACK DOOR SYSTEM (Power Back Door cannot be Operated Using Kick Sensor) |
| B | | GO TO SMART ACCESS SYSTEM WITH PUSH-BUTTON START (Back Door Entry Lock and Unlock Functions do not Operate) |
READ NEXT:
Lock Function (Entry Lock Function does not Operate Using Close &)
DESCRIPTION If the back door does not lock when using the power back door close and lock function, there may be communication problem between the certification ECU (smart key ECU assembly) and multipl
Entry Exterior Alarm and Answer-back Buzzer do not Sound
DESCRIPTION The smart access system with push-button start (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are
SEE MORE:
Removal
REMOVAL PROCEDURE 1. REMOVE BACK DOOR CENTER GARNISH Click here 2. REMOVE BACK DOOR SIDE GARNISH LH Click here 3. REMOVE BACK DOOR SIDE GARNISH RH Click here 4. REMOVE BACK DOOR TRIM BASE (w/ Power Back Door) Click here 5. REMOVE PULL HANDLE (w/ Power Back Door) Click here 6. REMOVE BACK D
Bus Buffer ECU Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Bus Buffer ECU Communication Stop Mode Any of the following conditions are met:
Communication stop for "Accessory Gateway" is indicated on the "Communication Bus Check" screen of the Techstream.
Click here
Communication system DTC
