Lexus NX: Operation Check
OPERATION CHECK
CHECK BASIC OPERATION
NOTICE:
-
This check is possible only when the "Power Back Door Function" customization setting using the multi-information display in the combination meter assembly is set to ON (initial setting is ON).
Click here
.gif)
- Before performing an operation check, check that the power back door system customization is set to its initial setting.
HINT:
During low temperatures, a clicking sound may be heard from the multiplex network door ECU, but this is not a malfunction.
(a) Conditions necessary for the power back door to open:
- The back door is unlocked (except wireless one motion function).
- The vehicle speed is 3 km/h (2 mph) or less (only when the power switch is on [IG]).
- The shift lever is in P, the brake pedal is depressed or the parking brake lever is pulled up (this can be determined only when the power switch is on [IG]).
(b) Check the opening operation.
(1) With the back door fully closed, push the combination switch assembly and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.
(2) With the back door fully closed, push the transmitter switch (electrical key transmitter sub-assembly) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.
(3) With the back door fully closed, push the back door opener switch assembly and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.
(c) Check the close operation.
(1) With the back door fully open, push the combination switch assembly and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.
(2) With the back door fully open, push the transmitter switch (electrical key transmitter sub-assembly) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.
(3) With the back door fully open, push the back door control switch and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.
(d) Check the operation when another input is detected during the opening or closing operation.
(1) During a power back door opening or closing operation, push the combination switch assembly again, and check that the power back door warning buzzer sounds for 0.2 seconds and the back door stops. After the closing operation stops, press the combination switch assembly and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.
(2) During a power back door opening or closing operation, push the transmitter switch (electrical key transmitter sub-assembly) again, and check that the power back door warning buzzer sounds for 0.2 seconds and the back door stops. After the closing operation stops, press the transmitter switch (electrical key transmitter sub-assembly) and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.
(3) During a power back door closing operation via the back door control switch, push the door control switch again, and check that the power back door warning buzzer sounds for 0.2 seconds and the power back door closing operation stops. After the closing operation stops, press the back door control switch and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.
(4) During a power back door opening or closing operation, push the back door opener switch assembly, and check that the power back door warning buzzer sounds for 0.2 seconds and the back door operation switches to manual operation mode.
(5) During a power back door opening or closing operation, push the door control switch, and check that the power back door warning buzzer sounds for 0.2 seconds and the back door stops.
(6) During a power back door opening or closing operation, kick operation and check that the power back door warning buzzer sounds for 0.2 seconds and the and the back door stops.*2
- *: w/ Hands Free Power Back Door
CHECK WIRELESS ONE MOTION FUNCTION
NOTICE:
-
This check is possible only when the "Power Back Door Function" customization setting using the multi-information display in the combination meter assembly is set to ON (initial setting is ON).
Click here
- Before performing an operation check, check that the power back door system customization is set to its initial setting.
- This check is possible only when the "One Motion with Unlock Door" customization setting using the Techstream is set to 0.8s or 2 Op (initial setting is Not Use).
(a) Check the wireless one motion operation.
(1) With all doors locked, push the transmitter switch (electrical key transmitter sub-assembly) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.
CHECK JAM PROTECTION FUNCTION
HINT:
- The power back door unit assembly set detects changes in the operating speed of the back door while the power back door is operating. If a change in the operating speed is out of the normal range, it will be judged that foreign objects are in the path of the power back door and the operation will stop if the door is operating in the opening direction or move a certain amount in the reverse direction if the door is operating in the closing direction.
- When the power back door sensor assemblies built into both sides of the back door are compressed, it is judged that foreign objects are in the path of the power back door and the operation will reverse a little in the opposite direction and then stop.
- The power back door sensor assemblies operate only while the back door is closing. They do not operate while the back door is opening.
(a) Check the jam protection function (the power back door sensor assembly) while the power back door is closing.
CAUTION:
Do not check this function using a part of your body such as your hand. Also, pay thorough attention that nothing gets caught by accident in this process.
(1) Fully open the back door.
(2) Press a switch to close the power back door.
(3) While the back door is closing, press a power back door sensor assembly using the handle of a hammer or equivalent.
(4) Check that the buzzer sounds twice for 0.1 seconds, the jam protection function is immediately activated and the power back door reverses a certain amount and stops.
(b) Check the jam protection function (the pulse sensor in the power back door unit assembly set) while the power back door is closing.
CAUTION:
Do not check this function using a part of your body such as your hand. Also, pay thorough attention that nothing gets caught by accident in this process.
(1) Fully open the back door.
(2) Press a switch to close the power back door.
(3) While the back door is closing, insert a tire or equivalent between the door panel and vehicle body, in order to interrupt the closing operation.
(4) Check that the buzzer sounds twice for 0.1 seconds, the jam protection function is immediately activated and the power back door reverses a certain amount and stops.
(c) Check the jam protection function while the power back door is opening.
CAUTION:
Do not check this function using a part of your body such as your hand. Also, pay thorough attention that nothing gets caught by accident in this process.
(1) Fully close the back door.
(2) Press a switch to open the power back door.
(3) While the back door is opening, use your hands to press on the outside surface of the back door panel so that the operating speed decreases.
(4) Check that the buzzer sounds twice for 0.1 seconds, the jam protection function is immediately activated and the power back door stops.
CHECK ASSIST OPERATION
(a) Check that the door automatically starts to fully close when the door is manually moved in the closing direction with the back door at rest.
CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When not using Techstream)
(a) Register open operation automatic stopped position in memory
(1) Open the back door by operating each switch.
(2) Operate each switch to stop the open operation when the back door reaches the desired automatic stopped position.
(3) When the back door control switch is pressed and held for 2 seconds or more with the back door at the stopped position, the buzzer sounds 4 times and the system memorizes the automatic stopped position for the open operation.
(4) Check that the back door stops at the memorized position when an open operation is performed with each switch.
(b) Clear open operation automatic stopped position memory
(1) Open the back door by operating each switch.
(2) Stop the back door by operating each switch.
(3) When the back door control switch is pressed and held for 7 seconds or more with the back door at the stopped position, the buzzer sounds 2 times and the system clears the automatic stopped position for the open operation.
CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When using Techstream)
(a) Register open operation automatic stopped position in memory
(1) Using the Techstream, select the "Power Back Door Opening Adjust" customize setting.
Click here
(2) According to the Techstream display, set the customize setting.
(3) Check that the back door stops at the position set with the customize function when an open operation is performed with each switch.
(b) Clear open operation automatic stopped position memory
(1) Open the back door by operating each switch.
(2) Stop the back door by operating each switch.
(3) When the back door control switch is pressed and held for 7 seconds or more with the back door at the stopped position, the buzzer sounds 2 times and the system clears the automatic stopped position for the open operation.
CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When using Multi-display)
(a) Register open operation automatic stopped position in memory
(1) Using the multi-display, select the "Power Back Door Opening Adjust" customize setting.
Click here
(2) According to the screen display, set the customize setting.
(3) Check that the back door stops at the position set with the customize function when an open operation is performed with each switch.
(b) Clear open operation automatic stopped position memory
(1) Open the back door by operating each switch.
(2) Stop the back door by operating each switch.
(3) When the back door control switch is pressed and held for 7 seconds or more with the back door at the stopped position, the buzzer sounds 2 times and the system clears the automatic stopped position for the open operation.
CHECK POWER BACK DOOR CLOSE AND LOCK FUNCION
(a) When the following conditions are met, check that all doors lock when pressing the door control switch after the power back door closes while carrying the transmitter switch (electrical key transmitter sub-assembly).
- Back door is open
- Door other than the back door is closed
- Transmitter switch (electrical key transmitter sub-assembly) is not in the vehicle
HINT:
If the door control switch is operated with the hand holding the transmitter switch (electrical key transmitter sub-assembly), it may not operate due to being outside the key detection area.
CHECK HANDS FREE POWER BACK DOOR OPERATION (w/ Hands Free Power Back Door)
NOTICE:
-
This function operates when the "Kick Sensor Operation Function" item is set to "OFF" using the Techstream customization function (The default setting is "ON").
Click here
-
This function operates when the "Kick Sensor" item is set to "OFF" using the customization function via the multi-information display in the combination meter assembly (The default setting is "ON").
Click here
(a) With the except hybrid control system was started and the electrical key transmitter sub-assembly (electrical key) being carried, check that the power back door operates when a kick operation is performed within 100 mm of the rear bumper surface.
| *1 | Kick Door Control Sensor | - | - |
| *a | 100 mm (3.94 in.) | *b | Center of the rear bumper |
HINT:
- The hands free power trunk lid detects a change in electrostatic capacitance in the detection area of the kick door control sensor (Operation trigger).
- Placing your leg or a metallic object within 100 mm of the rear bumper surface and then moving it out of the detection area results in the hands free power trunk lid operating due to the kick door control sensor detecting a change in electrostatic capacitance.
- The kick door control sensor receives vehicle speed, IG and ACC signals from the main body ECU (multiplex network body ECU) via LIN communication and uses the information to stop sensor oscillation.
READ NEXT:
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE POWER BACK DOOR SYSTEM HINT: The following items can be customized. NOTICE:
When the customer requests a change in a function, first make sure that the function can b
Initialization
INITIALIZATION INITIALIZE MULTIPLEX NETWORK DOOR ECU NOTICE: Initialization of the multiplex network door ECU (back door initial position learning) is necessary if the following work procedures are pe
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of
SEE MORE:
Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be dis
Indicator Circuit
DESCRIPTION In accordance with the shift lever position, each shift position indicator light will turn on. WIRING DIAGRAM PROCEDURE 1. CHECK SHIFT POSITION INDICATOR (a) Turn the power switch on (ACC). (b) Check that each shift position indicator light turns on correctly. Result Proce
