Lexus NX: Parts Location
PARTS LOCATION
ILLUSTRATION
| *1 | MAP LIGHT ASSEMBLY | *2 | SPOT LIGHT ASSEMBLY |
| *3 | VISOR ASSEMBLY RH | *4 | VISOR ASSEMBLY LH |
| *5 | VANITY LIGHT ASSEMBLY RH | *6 | VANITY LIGHT ASSEMBLY LH |
| *7 | FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH | *8 | FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH |
| *9 | REAR DOOR OUTSIDE HANDLE ASSEMBLY RH | *10 | REAR DOOR OUTSIDE HANDLE ASSEMBLY LH |
| *11 | NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY RH | *12 | NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY LH |
| *13 | ENGINE ROOM RELAY BLOCK - AM2 FUSE - ECU-B NO.5 FUSE | *14 | NO. 2 ENGINE ROOM RELAY BLOCK - DOME FUSE |
ILLUSTRATION
| *A | w/o Power Back Door System | *B | w/ Power Back Door System |
| *1 | BACK DOOR LOCK ASSEMBLY | *2 | FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH |
| *3 | FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH | *4 | FRONT DOOR LOCK ASSEMBLY RH |
| *5 | FRONT DOOR LOCK ASSEMBLY LH | *6 | REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH |
| *7 | REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH | *8 | REAR DOOR LOCK ASSEMBLY RH |
| *9 | REAR DOOR LOCK ASSEMBLY LH | *10 | BACK DOOR COURTESY LIGHT SWITCH |
ILLUSTRATION
| *A | w/ Navigation System | - | - |
| *1 | GLOVE BOX LIGHT ASSEMBLY | *2 | POWER SWITCH |
| *3 | HEADLIGHT DIMMER SWITCH ASSEMBLY | *4 | CONSOLE BOX ILLUMINATION LIGHT ASSEMBLY |
| *5 | NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY RH | *6 | NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY LH |
| *7 | CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) | *8 | REMOTE OPERATION CONTROLLER ASSEMBLY |
| *9 | NO. 3 RELAY BLOCK - DOME CUT RELAY | *10 | MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| *11 | INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - TAIL RELAY - ACC RELAY - IG1 NO.2 RELAY - ACC FUSE - ECU-IG NO.2 FUSE - PANEL FUSE | *12 | DLC3 |
READ NEXT:
System Diagram
SYSTEM DIAGRAM
System Description
SYSTEM DESCRIPTION ILLUMINATION CONTROL SYSTEM (Illuminated Entry System) HINT: When inspecting the following functions, make sure that the map light switch and spot light switch are in the DOOR posit
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT:
Use the following procedure to troubleshoot the lighting system.
*: Use the Techstream.
PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP
NEXT
SEE MORE:
Operation Check
OPERATION CHECK REMOTE TOUCH SELF CHECK NOTICE:
Before entering self-diagnostic mode, make sure there are no obstacles which may interfere with operation of the remote touch screen, and that the touch screen is not dirty.
Do not touch the touch screen except when required.
Since the remote to
Drive Motor "A" Inverter Voltage Sensor Circuit Low (P0D2F-266,P0D30-267)
DESCRIPTION The inverter contains a three-phase bridge circuit, which consists of 6 power transistors (IGBTs) each for the generator (MG1), motor (MG2) and rear motor (MGR). The inverter converts high-voltage direct current from the HV battery into three-phase alternating current for the generator (
