Lexus NX: Radio Receiver Assembly Communication Stop Mode

Lexus NX Service Manual / Power Source & Network / Networking / Can Communication System / Radio Receiver Assembly Communication Stop Mode

DESCRIPTION

Detection Item	Symptom	Trouble Area
Radio Receiver Assembly Communication Stop Mode	Any of the following conditions are met: Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the Techstream. Click here Communication system DTCs (DTCs that start with U) that correspond to "Radio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" are output. Click here	Radio receiver assembly branch wire or connector Power source circuit of radio receiver assembly Radio receiver assembly ground circuit Radio receiver assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here
When disconnecting and reconnecting the auxiliary battery.
Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here
Some parts must be initialized and set when replacing or removing and installing parts.
Click here
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
The following malfunctions may occur if a radio receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio receiver assembly, be sure to replace it with new one.
- Communication malfunction DTC is output
- Does not operate normally

HINT:

Operating the power switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.	CHECK FOR OPEN IN CAN BUS WIRE (RADIO RECEIVER ASSEMBLY BRANCH WIRE)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

(b) Disconnect the radio receiver assembly connector.

*a	Front view of wire harness connector (to Radio Receiver Assembly)

Standard Resistance:

Tester Connection	Condition	Specified Condition
I152-13 (CANH) - I152-14 (CANL)	Cable disconnected from negative (-) auxiliary battery terminal	54 to 69 Ω

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.	CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Disconnect the radio receiver assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Front view of wire harness connector

(to Radio Receiver Assembly)

Standard Resistance:

Tester Connection	Condition	Specified Condition
I151-1 (GND1) - Body ground	Cable disconnected from negative (-) auxiliary battery terminal	Below 1 Ω

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
I151-4 (+B1) - Body ground	Power switch off	11 to 14 V
I151-15 (ACC1) - Body ground	Power switch on (ACC)	11 to 14 V
I151-15 (ACC1) - Body ground	Power switch off	Below 1 V
I152-19 (IG) - Body ground	Power switch on (IG)	11 to 14 V
I152-19 (IG) - Body ground	Power switch off	Below 1 V

REPLACE RADIO RECEIVER ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

SEE MORE:

ECM / PCM Processor (P0606)

MONITOR DESCRIPTION The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from these CPUs are different and deviate from the standard, the ECM will illuminate the MIL and store this DTC. DTC No. Detection Item DTC Detecti

Driver Side Camera Video Sync Signal Malfunction (C1686)

DESCRIPTION This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU. DTC No. Detection Item DTC Detection Condition Troubl

Lexus NX: Radio Receiver Assembly Communication Stop Mode

READ NEXT:

Blind Spot Monitor Sensor Communication Stop Mode

Bus Buffer ECU Communication Stop Mode

DCM Communication Stop Mode

SEE MORE:

ECM / PCM Processor (P0606)

Driver Side Camera Video Sync Signal Malfunction (C1686)