Lexus NX: Rear Axle Hub Bolt
Components
COMPONENTS
ILLUSTRATION
| *1 | REAR AXLE HUB BOLT LH | *2 | REAR DISC |
| *3 | REAR DISC BRAKE CALIPER ASSEMBLY LH | - | - |
.png) | N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
Replacement
REPLACEMENT
CAUTION / NOTICE / HINT
NOTICE:
- When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.
- While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake shoes are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.
(Click here .gif)
)
2. DISABLE BRAKE CONTROL
Click here
3. REMOVE REAR WHEEL
Click here
4. DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH
| (a) Disconnect the parking brake wire from the rear disc brake caliper assembly LH. |
|
| (b) Remove the 2 bolts, and disconnect the rear disc brake caliper assembly. NOTICE: Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose. |
|
5. REMOVE REAR DISC
Click here
6. REMOVE REAR AXLE HUB BOLT LH
| (a) Temporarily install 2 nuts and 2 washers to the rear axle hub bolt as shown in the illustration. |
|
(b) Using SST and a brass bar or an equivalent tool to hold the hub and bearing assembly, remove the rear axle hub bolt.
SST: 09611-12010
7. INSTALL REAR AXLE HUB BOLT LH
| (a) Install a washer and nut to a new rear axle hub bolt as shown in the illustration. |
|
(b) Using a brass bar or an equivalent tool to hold the hub and bearing assembly, install the rear axle hub bolt by tightening the nut.
8. INSTALL REAR DISC
Click here
9. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH
(a) Connect the rear disc brake caliper assembly LH with the 2 bolts.
Torque:
104 N·m {1061 kgf·cm, 77 ft·lbf}
(b) Connect the parking brake wrie to the rear disc brake caliper assembly LH.
10. INSTALL REAR WHEEL
Click here
11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
(a) Connect the cable to the negative (-) auxiliary battery terminal and tighten the nut.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
READ NEXT:
Steering Knuckle
ComponentsCOMPONENTS ILLUSTRATION *1 FRONT AXLE HUB SUB-ASSEMBLY LH *2 FRONT LOWER BALL JOINT ASSEMBLY LH *3 STEERING KNUCKLE LH *4 FRONT BRAKE DUST COVER N*m (kgf*cm, ft.*
Drive Shaft System
Problem Symptoms TablePROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms ar
SEE MORE:
Removal
REMOVAL PROCEDURE 1. DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column) (a) Disable the autoaway/return function by changing the customize parameter. Click here CAUTION: Record the current customize parameter setting (whether the autoaway/return function is enab
A/C Inverter Load System Malfunction (B1476)
DESCRIPTION The operation of the compressor with motor assembly is stopped and this DTC is stored if the rotation load is too large or too small while the compressor with motor assembly is operating. Possible causes are refrigerant leaks, overcharged refrigerant, insufficient cooling due to a conden
