Lexus NX: Warning Notification Function Malfunction
CAUTION / NOTICE / HINT
NOTICE:
When replacing the radio receiver assembly, always replace it with a new one.
If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio receiver assembly may not operate normally.
PROCEDURE
| 1. | CHECK PROBLEM SYMPTOM (WARNING NOTIFICATION FUNCTION) |
(a) Check the problem symptom.
(1) Check the problem symptom of the warning notification function.
| Result | Proceed to |
|---|---|
| The multi-display assembly screen does not show a warning message even though a warning light turns on or the multi-information display indicates a warning. | A |
| The multi-display assembly screen shows a warning message even though a warning light is not on and the multi-information display does not indicate a warning. | B |
| The multi-display assembly screen shows a warning message different from the warning light or the multi-information display. |
HINT:
- The warning notification function sends information to the service center through communication.
- Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal conditions caused the malfunction.
| B | .gif) | GO TO STEP 8 |
|
.gif)
| 2. | INSPECT WARNING LIGHT |
(a) Check if the indicated warning light or message is listed in the following table.
HINT:
Only messages listed in the table are included in the warning notification function.
| Warning Name |
|---|
| Engine warning |
| Hybrid control system warning |
| Brake system warning |
| VSC warning |
| ABS warning |
| ECB warning |
| EPS warning |
| Charging system warning |
| Airbag warning |
| PCS warning |
| Cruise warning |
| Intuitive parking assist system warning |
| Drive start control system |
| Brake override system warning |
| Smart access system with push-button start warning |
| Automatic headlight beam level control system warning |
| AFS warning |
| Automatic high beam system warning |
| LED headlight warning |
| 4WD warning |
| Tire pressure system warning |
| Electric parking brake warning |
| Auto hold warning |
| BSM system warning |
| Lane departure alert system warning |
| Vehicle proximity notification system warning |
| Intelligent clearance sonar system warning |
| LTA system warning |
| RSA system warning |
| Engine oil pressure warning |
| Tire pressure low warning |
| Washer fluid level warning |
| Engine oil maintenance warning |
| High coolant temperature warning |
| Hybrid system temperature warning |
| Hybrid battery cooling fan maintenance warning |
| Maintenance advice warning |
| Towing prohibited warning |
| Result | Proceed to |
|---|---|
| Warning light or message is listed in the table. | A |
| Warning light or message is not listed in the table. | B |
| B | | END |
|
| 3. | CHECK CAN COMMUNICATION SYSTEM |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Bus Check.
(e) Check that all ECUs and sensors that use CAN communication are connected.
Click here .gif)
| Result | Proceed to |
|---|---|
| There are no connection problems. | A |
| There is a connection problem. | B |
| B | | GO TO CAN COMMUNICATION SYSTEM |
|
| 4. | CHECK METER WARNING LIGHT |
(a) Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.
OK:
There are no problems with warning lights or warning messages.
HINT:
The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.
| NG | | GO TO METER / GAUGE SYSTEM |
|
| 5. | CHECK VEHICLE TYPE |
(a) Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Navigation System | A |
| w/o Navigation System | B |
| B | | GO TO STEP 7 |
|
| 6. | CHECK NAVIGATION SYSTEM |
(a) Check if the navigation system is operating and functioning normally.
OK:
The navigation system is normal.
| OK | | REPLACE RADIO RECEIVER ASSEMBLY |
| NG | | GO TO NAVIGATION SYSTEM |
| 7. | CHECK AUDIO AND VISUAL SYSTEM |
(a) Check if the audio and visual system is operating and functioning normally.
OK:
The audio and visual system is normal.
| OK | | REPLACE RADIO RECEIVER ASSEMBLY |
| NG | | GO TO AUDIO AND VISUAL SYSTEM |
| 8. | CHECK METER WARNING LIGHT |
(a) Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.
OK:
There are no problems with warning lights or warning messages.
HINT:
The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.
| OK | | REPLACE RADIO RECEIVER ASSEMBLY |
| NG | | GO TO METER / GAUGE SYSTEM |
READ NEXT:
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop. PROCEDURE 1. REMOVE SERVICE PLUG GRIP Click here 2. REMOVE WINDSHIELD WIPER MO
Inspection
INSPECTION PROCEDURE 1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH NOTICE:
Do not apply voltage to any terminals except terminals 1 and 2 to avoid damaging the pulse sensor inside the motor.
Reset the power window regulator motor (initialize the pulse sensor) after installing the power wi
