Lexus NX: Power Mirror cannot be Adjusted with Power Mirror Switch
DESCRIPTION
When the outer mirror switch assembly mirror select switch is operated, right/left selection signals are sent to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) sends the received right/left selection signals to the outer mirror control ECU assemblies via CAN communication.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.
Click here
.gif)
-
If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.
Click here
PROCEDURE
| 1. | READ VALUE USING TECHSTREAM (OUTER MIRROR SWITCH ASSEMBLY) |
(a) Using the Techstream, read the Data List.
Click here
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mirror Selection SW (R) | Mirror select switch signal for RH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch R switch on | - |
| Mirror Selection SW (L) | Mirror select switch signal for LH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch L switch on | - |
| Mirror Position SW (R) | Mirror surface adjust switch signal (Right) | OFF or ON | OFF: Mirror surface adjust switch not pressed right ON: Mirror surface adjust switch pressed right | Check with the mirror select switch L or R switch on |
| Mirror Position SW (L) | Mirror surface adjust switch signal (Left) | OFF or ON | OFF: Mirror surface adjust switch not pressed left ON: Mirror surface adjust switch pressed left | Check with the mirror select switch L or R switch on |
| Mirror Position SW (Up) | Mirror surface adjust switch signal (Up) | OFF or ON | OFF: Mirror surface adjust switch not pressed up ON: Mirror surface adjust switch pressed up | Check with the mirror select switch L or R switch on |
| Mirror Position SW (Dwn) | Mirror surface adjust switch signal (Down) | OFF or ON | OFF: Mirror surface adjust switch not pressed down ON: Mirror surface adjust switch pressed down | Check with the mirror select switch L or R switch on |
| Tester Display |
|---|
| Mirror Selection SW (R) |
| Mirror Selection SW (L) |
| Mirror Position SW (R) |
| Mirror Position SW (L) |
| Mirror Position SW (Up) |
| Mirror Position SW (Dwn) |
OK:
The display is as specified in the normal condition column.
| OK | .gif) | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
|
.gif)
| 2. | INSPECT OUTER MIRROR SWITCH ASSEMBLY |
(a) Remove the outer mirror switch assembly.
Click here
(b) Inspect the outer mirror switch assembly.
Click here
| NG | | REPLACE OUTER MIRROR SWITCH ASSEMBLY |
|
| 3. | CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU]) |
(a) Disconnect the I49 main body ECU (multiplex network body ECU) connector.
(b) Disconnect the M13 outer mirror switch assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M13-13 (M+) - I49-4 (MIRB) | Always | Below 1 Ω |
| M13-14 (MSW) - I49-5 (MIRS) | Always | Below 1 Ω |
| M13-12 (E) - I49-6 (MIRE) | Always | Below 1 Ω |
| M13-13 (M+) or I49-4 (MIRB) - Body ground | Always | 10 kΩ or higher |
| M13-14 (MSW) or I49-5 (MIRS) - Body ground | Always | 10 kΩ or higher |
| M13-12 (E) or I49-6 (MIRE) - Body ground | Always | 10 kΩ or higher |
| OK | | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
Mirror Heater does not Operate with Rear Defogger Switch
DESCRIPTION When therear window defogger switch (mirror heater switch) is operated, a mirror heater signal is sent to the air conditioning amplifier assembly via LIN communication. The air conditionin
Power Retractable Mirrors do not Operate with Power Retract Mirror Switch
DESCRIPTION When the outer mirror switch assembly mirror retract switch is operated, deploy/retract signals are sent to the main body ECU (multiplex network body ECU). The main body ECU (multiplex net
AUTO Power Retract Mirrors do not operate
DESCRIPTION When the outer mirror switch assembly is set to AUTO (neutral position), an AUTO signal is detected by the main body ECU (multiplex network body ECU). When locking and unlocking all doors
SEE MORE:
On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the front seat outer belt assembly. PROCEDURE 1. INSPECT FRONT SEAT OUTER BELT ASSEMBLY (for Vehicle not Involved in Collision) (a) Perform a diagnostic system check. Click
Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PROCEDURE 1. INSTALL FRONT AIRBAG SENSOR LH (a) Check that the power switch is off. (b) Check that the cable is disconnected from the negative (-) auxilia
