Lexus NX: System Description

SYSTEM DESCRIPTION

DESCRIPTION

(a) Safety Connect performs ACN (Automatic Collision Notification), manual emergency calling, stolen vehicle tracking and roadside assistance service, by audio and data communications between the vehicle and call center through a cellular phone network. As shown in the illustration, when a collision is detected, the vehicle sends its location calculated based on GPS signals and the identification code of the DCM (telematics transceiver) to a call center. After the necessary information has been gathered, the call center will relay this information to emergency services.

*: Public Safety Answering Point

SYSTEM FUNCTION

(a) ACN (Automatic Collision Notification)

(1) When a collision is detected, the vehicle connects to the call center automatically and reports the vehicle location and vehicle information by data communication. The operator will connect to the vehicle and communicate with the occupant. Even if the occupant does not answer, the operator can notify emergency services.

(b) Manual Emergency Call

(1) After pressing the manual (SOS) switch, the occupant can talk to an operator from the call center to seek assistance.

(c) Stolen Vehicle Locator

(1) After the vehicle has been reported stolen to the police, the customer can contact the call center to begin the stolen vehicle locator process. The operator locates this vehicle by GPS and provides information to the police.

(d) Roadside Assistance Service

(1) Pressing the manual (SOS) switch will contact the call center, and a wide range of help, such as towing, flat tire, fuel delivery, etc. can be provided.

*: Public Safety Answering Point

HINT:

The shape of the manual (SOS) switch shown in the illustration is an example, and may differ from that of an actual vehicle.

VOICE GUIDANCE FUNCTION

HINT:

The system plays back the following voice prompts in the situations shown.

Voice Prompt

Usage Condition

Communication Module failure detected, please contact your dealer.

When system detects LED failure (Red only), and another DTC is stored.

Message is played once at each power switch on (IG) until the problem is fixed.

Connecting to the Call Center.

DCM Activation start.

Communication Module Activation Failed.

DCM Activation fails for some reason.

Communication Module Activation complete.

DCM Activation completed normally.

If you continue to receive this message, contact your dealer.

Follows Port Activation Sequence.

Unable to Connect to the Call Center.

When system not able to connect activation call center.

Impact detected.

When DCM (telematics transceiver) receives collision detection signal.

Connecting to the Emergency Call Center.

Call initiated to call center.

Unable to Connect to the Emergency Call Center.

DCM (telematics transceiver) cannot connect to Emergency Call Center for some reason.

To cancel, please press the button again.

To end the call manually.

Emergency call canceled.

Confirmation that the call has been canceled.

The system will try again.

Could not connect to call center.

To activate, please press the button again within 5 seconds.

This voice prompt is instruction for activation.

Safety Connect is not active.

When Safety Connect is not active.

INDICATOR CONTROL FUNCTION DURING DCM (TELEMATICS TRANSCEIVER) SELF CHECK MODE

HINT:

Every time after the power switch is turned on (IG), the DCM (telematics transceiver) will enter into a self check mode. The manual (SOS) switch red indicator will illuminate for 2 seconds and then turn off and then the manual (SOS) switch green indicator will illuminate and will stay on throughout normal operation. The following chart indicates the possible scenarios.

  • *1: The red and green indicators alternate turning on and off at 2-second intervals until the DCM (telematics transceiver) completes auto activation. System will automatically switch to shipping mode or active mode if auto activation is successful.
  • *2: If a call is in progress while the power switch off, the call will continue and the LED function will not change.

SWITCHING CONTRACT MODES

Contract Mode

Description

Shipping Mode

The vehicle is being transported or service is canceled.

Services do not operate.

Active Mode

Services can operate.

However, the only services that operate are ones the customer are subscribed to.

READ NEXT:

 How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the safety connect system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT

 Dcm Operation History

DCM OPERATION HISTORY HINT: This function shows the telematics network status when the DCM (telematics transceiver) was operated. Use this when no DTC is present but this telematics system was unab

 Dcm Activation

DCM ACTIVATION DCM ACTIVATION (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Choose "Telematics" from the System Selection Menu, and then cl

SEE MORE:

 Installation

INSTALLATION PROCEDURE 1. INSTALL TILT AND TELESCOPIC SWITCH (a) Attach the claw to install the tilt and telescopic switch. (b) Connect the connector. 2. INSTALL LOWER STEERING COLUMN COVER (a) Attach the 2 claws to install the lower steering column cover. NOTICE: Do not damage the tilt and telescop

 Data List / Active Test

DATA LIST / ACTIVE TEST DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be dis

© 2016-2024 Copyright www.lexunx.com