Lexus NX: Detecting Vehicle Submersion (B2277)
DESCRIPTION
This DTC is stored when a malfunction in the water submersion detection circuit in the certification ECU (smart key ECU assembly) is detected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2277 | Detecting Vehicle Submersion | The water submersion detection circuit in the certification ECU (smart key ECU assembly) detects water submersion (1-trip detection logic*). | Certification ECU (smart key ECU assembly) |
|
- *: Only detected while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The power switch cannot be turned off and the hybrid control system cannot be started. | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2277 | - |
CAUTION / NOTICE / HINT
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
-
The smart access system with push-button start (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart access system with push-button start (for Start Function) after confirming that the communication systems are functioning properly.
Click here
.gif)
-
Before replacing the certification ECU (smart key ECU assembly), refer to the smart access system with push-button start (for Start Function) Precaution.
Click here
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
HINT:
- Before proceeding with troubleshooting, check if there are any signs of water damage to the certification ECU (smart key ECU assembly). If there are any signs of water damage, replace the certification ECU (smart key ECU assembly) and take measures against the cause of the water damage.
- When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
PROCEDURE
| 1. | CHECK WATER INTRUSION |
(a) Check that the certification ECU (smart key ECU assembly), its surrounding area and wire harnesses have no signs of water intrusion.
| Result | Proceed to |
|---|---|
| No sign of water intrusion found | A |
| Signs of water intrusion found | B |
| A | .gif) | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| B | | TAKE MEASURES FOR WATER INTRUSION AND REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
READ NEXT:
Vehicle Speed Signal Malfunction (B2282,B2283)
DESCRIPTION DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match. DTC B2283 is
Steering Lock Position Signal Circuit Malfunction (B2285)
DESCRIPTION This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN
Lost Communication with Main Body ECU (U0140,U0142,U0155,U0293,U1117)
DESCRIPTION These DTCs are stored when there is a CAN communication error between the hybrid vehicle control ECU, certification ECU (smart key ECU assembly), ECM, main body ECU (multiplex network body
SEE MORE:
Terminals Of Ecu
TERMINALS OF ECU CHECK DCM (TELEMATICS TRANSCEIVER) Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition I183-1 (+B) - I183-20 (E) Y - W-B Power source (+B) Power switch off 11 to 14 V I183-3 (SIG-) - I183-20 (E) G - W-B Ground Alway
Terminals Of Ecu
TERMINALS OF ECU *a Component with harness connected (Power Steering ECU Assembly) - - CHECK POWER STEERING ECU ASSEMBLY (a) Measure the voltage and resistance according to the value(s) in the table below. NOTICE: When the power steering warning light (red) is illuminated due to a malfu
